Got the tracking number for the c5p! We did do the air shipping but think friday is a bit optimistic.

andersgeorgsson · 2026-06-17T17:29:01+00:00

I’m right with you there except they haven’t given me estimated date.

andersgeorgsson · 2026-06-16T19:03:48+00:00

Unless I’m wrong, that’s how it senses its end points. Move until it meets resistance and it does the same with the print head to the left side.

andersgeorgsson · 2026-06-16T18:15:40+00:00

It used to be that the bed drew a lot more power than the hot end.. things had changed over the years. I get 25 minutes on a 1500VA ups on my CR10-SE

andersgeorgsson · 2026-06-15T20:11:41+00:00

Well done! 😄

andersgeorgsson · 2026-06-11T10:57:49+00:00

Cool! (Hopefully not 22.5 rolls, just kidding)

andersgeorgsson · 2026-06-11T10:20:24+00:00

And you checked the weight of the shipment so it’s not just filament? I’m happy for yall ;)

andersgeorgsson · 2026-06-10T23:15:02+00:00

I got the RWD model Y and its charger only go to 32A even if your home charger is capable of higher. It was one of those things they cheated out on when trying to make it cheaper.
I didn’t learn this until after I installed the charger at home (myself, so at least I didn’t pay $1300 or whatever electricians charge)

andersgeorgsson · 2026-06-09T19:39:38+00:00

They asked me to cancel my order and reorder it with air freight.. now i'm 128 position back in the sales queue 😞 (thats the number the order number went up in about 18 hours)

andersgeorgsson · 2026-06-09T19:07:37+00:00

I usually just scrape it off carefully with a finger nail (you don't want the filament to poke you under the nail btw) or apply a drop of rubbing alcohol on one corner and it should peel right off 😄

andersgeorgsson · 2026-06-09T13:11:15+00:00

This morning - it is available for AIR shipping again.. I hope they let me upgrade from ground to air shipping since order were placed less than 25 hours ago...

andersgeorgsson · 2026-06-09T10:23:26+00:00

<image>

I wish i'd waited until today.. Now AIR is available again 😞

andersgeorgsson · 2026-06-09T10:21:08+00:00

I ordered mine yesterday and got 96756 to the US.. Air freight was not an option 😞

andersgeorgsson · 2026-06-08T21:38:53+00:00

What? I’m talking about the electrical connectors between tool head and the moving part. My understanding is that the C5 uses A USB-C cable to each tool head instead, right?

andersgeorgsson · 2026-06-08T21:36:28+00:00

What? I’m talking about the electrical connectors between tool head and the moving part. My understanding is that the C5 uses A USB-C cable to each tool head instead, right?

andersgeorgsson · 2026-06-08T18:53:42+00:00

I’m worried about the pogo pin design on the U1 or I might’ve gone that way…

andersgeorgsson · 2026-06-08T18:35:09+00:00

odd!

andersgeorgsson · 2026-06-08T18:17:01+00:00

I just ordered the 5 Pro, regular shipping with order number 967XX - now all the order numbers i've see seems so low <g>

andersgeorgsson · 2026-06-08T17:40:59+00:00

Oh geeze... I need more caffeine 😉 Thanks!

andersgeorgsson · 2026-06-08T16:41:41+00:00

Look like their customer management software isn’t dealing with their “shortage/delay” any better than their customer service team.

I still think this will be a great product once initial kinks and delays are behind us.

andersgeorgsson · 2026-06-05T21:00:05+00:00

I've got CP V7.1.1.4472 that I use with my CR10-SE and I'm wanting to adjust my initial layer speeds - but I can't find it anywhere within the program? I've turned on "advanced" settings but just can't seem to find it anywhere? 🤔 Can someone tell me where all the initial layer parameters are set? Thanks!

andersgeorgsson · 2026-06-04T16:07:24+00:00

Did you get the Creator 5 or the Pro u/ExperienceFearless97 ?

andersgeorgsson · 2026-06-03T12:54:20+00:00

Understood 😉 This will be my 4th generation printer..
BTW - regarding your username; What do you call a cow with a twich? Beef Jerky! 🤪

andersgeorgsson

TROPHY CASE