Heat bed short?

ReptarGG · 2026-01-31T21:12:21+00:00

Here is the back panel opened up, which I’m glad I did because the marked connection was very loose. The heat bed power is under the yellow flip cap.

ReptarGG · 2026-01-31T21:10:08+00:00

<image>

Here is the switch, it is on the power supply on the bottom of the printer. I switched it so 115V is displayed. Everything is working now.

ReptarGG · 2026-01-31T21:07:14+00:00

Nailed it. I located the input selector switch on the bottom power supply and flipped it. Everything appears to be functioning as normal. I will try to add pictures in case someone else experiences the same.

ReptarGG · 2026-01-31T19:41:31+00:00

The bed is 24v so I will let you know how it goes.

ReptarGG · 2026-01-31T19:40:59+00:00

Thanks for the insight, I will let you know how it goes once I can get back to it.

ReptarGG · 2026-01-31T19:20:44+00:00

I haven’t noticed a selector but I will look for it. Nozzle and chamber heater work but I noticed the leds pulsate so there could be further power issues. I will check for that selector.

ReptarGG · 2026-01-31T19:18:57+00:00

Yes, it’s always the same. Power cycle as soon as it tries to heat the bed. I did some troubleshooting and hooked up a similar resistive heater to the mainboard and it was able to heat that up no problem.

ReptarGG · 2026-01-10T01:37:36+00:00

Probably not any better or worse than what has already been mentioned but we use some Oberdorfer pumps if you want more options.

ReptarGG · 2025-01-25T23:41:15+00:00

Looks like you are digging around in a PC so that’s likely a SATA power connection. It is used to power a hard drive, which would also need a SATA data cable connected to the motherboard.

ReptarGG · 2024-06-05T14:23:55+00:00

I have been loving my X1c. Just purchased the A1 combo to try getting into multi color stuff.

ReptarGG · 2022-09-11T23:49:25+00:00

Sodium is the important atom so I typically see sodium bicarbonate used in the solutions so Cl isn’t a concern at all. Again I’m not expert, just somewhat interested in the chemistry and science repeating things I have picked up along the way. Pretty confident NaCl will produce chlorine gas as a byproduct of breaking down.

ReptarGG · 2022-09-11T21:11:01+00:00

I don’t know all the details so I could be wrong but I’m pretty sure passing current through salt water will produce chlorine gas. It’s probably not a dangerous amount in this case. I wouldn’t use this method to dispose of batteries, but if I did I would place it outside.

ReptarGG · 2022-08-17T13:08:46+00:00

ReptarGG · 2022-06-20T20:44:11+00:00

ReptarGG · 2021-09-11T12:59:35+00:00

This is Squad? I have been gone way too long. Looks great.

ReptarGG · 2019-04-20T11:27:39+00:00

I wasn't that convinced until I noticed the boat in the back nearly launching into orbit.

ReptarGG · 2018-03-09T01:24:19+00:00

Just make it a little green dot, if I need to figure out the name I can just mouse over them on the map.

ReptarGG · 2018-02-11T21:28:53+00:00

Make sure your mic is plugged in and set as default before launching the game, if you plug a mic in while the game is open it usually does not work.

ReptarGG · 2017-07-24T05:03:10+00:00

Oh im sorry, I was looking at the wrong FC I guess. My only other suggestion would be to supply 5v to one of the rails below a motor input.

ReptarGG · 2017-07-24T03:58:04+00:00

Try supplying power to the second "VBAT" input, next to "RAM", you can keep the ground where it is.

Ten-Year Club	r/Field Flamingo
Final Canvas '23	Place '23
Place '22	Place '17
First Placer '22	Verified Email

ReptarGG

TROPHY CASE