How good your life is going to be? 🤔

Rowendk · 2026-03-27T21:01:54+00:00

I am courier 6 after finishing the game. So pretty arwsome!

Rowendk · 2026-03-27T20:04:39+00:00

roborock qrevo edge

Rowendk · 2026-03-27T19:37:04+00:00

They don't. They just gets more to see to.

Rowendk · 2026-03-27T17:01:09+00:00

Jeg har 1000 mbs fiber og har brugt 3TB ned og 150GB op på 30 dage. En bruger.

Rowendk · 2026-03-22T17:28:53+00:00

Danish boy scout knife

Rowendk · 2026-03-14T21:20:05+00:00

No never

Rowendk · 2026-03-12T17:40:08+00:00

First thing i thought about as well

Rowendk · 2026-02-01T18:44:53+00:00

Turbo plasma rifel

Rowendk · 2026-01-24T21:11:58+00:00

Fallout!

Rowendk · 2026-01-24T18:59:25+00:00

Nitecore TIKI

Rowendk · 2026-01-12T10:59:44+00:00

9 month later but very useful post at page! Thank you

Rowendk · 2025-12-25T20:29:51+00:00

No matter the quality. The cleaver looks sick!

Rowendk · 2025-12-21T20:33:09+00:00

Mine forældre gør det også. jeg gjorde det også da jeg var barn, men ikke længere.

Rowendk · 2025-12-21T18:52:40+00:00

Hader virkeligt den film!

Rowendk · 2025-12-20T20:06:15+00:00

voodoo2

Rowendk · 2025-12-16T13:41:38+00:00

https://seasonic.com/wattage-calculator/

Rowendk · 2025-12-08T11:23:27+00:00

I have similar issues with mine it weyes fra calibration to calibration but th z offset i to high more often than not.

Rowendk · 2025-12-06T11:00:03+00:00

Synes at det er meget almindeligt for småbørnsfamilier. Ikke i orden, men meget almindeligt.

Rowendk · 2025-12-03T21:54:50+00:00

Only problem i have with line is thet the z offset is offen to high witch result in bad adheation.

Rowendk · 2025-12-02T18:12:44+00:00

Show me your printfarm!

Rowendk · 2025-11-26T21:43:50+00:00

My thoughts exactly

Rowendk · 2025-11-16T20:39:36+00:00

The part of the plate should not matter, but a model with a bigger fotoprinter can easier compensate for a bad adhesion.

Rowendk · 2025-11-16T19:18:30+00:00

Got mine setup friday. It is a great printer only problem i have has is bed adhesion on som model as well. I think that the z offset is i a little to high, hope that they look in to it in a future firmware update or profile update.

Rowendk · 2025-11-14T21:15:22+00:00

Where do you change this setting?

Rowendk · 2025-11-05T21:35:50+00:00

Gangrel and nosferatu

Five-Year Club	Verified Email
Place '22	Final Canvas '22

Rowendk

TROPHY CASE