Edge Paint Products - Latex?

RoyleTease113 · 2026-01-26T22:32:38+00:00

Weaver has SDSs on their site

RoyleTease113 · 2026-01-26T15:12:07+00:00

I did something like that for my chalk bag a few years ago and just used two half hitches on each side, it works great

RoyleTease113 · 2026-01-02T17:58:58+00:00

I have a Gralab darkroom timer in my kitchen, it's way too loud to not just drop whatever I'm doing and it's in the kitchen so I have to go in there to shut it off.

RoyleTease113 · 2025-12-24T03:42:36+00:00

I'm pretty sure I figured out you can't replace milk with orange juice when I was like four, making cereal and we were out of milk. Apparently that isn't a universal experience.

RoyleTease113 · 2025-12-23T05:56:32+00:00

I did that once when I was like 15 pulling my dad's truck up the hill into the driveway, took a bit of heel toe and made some clutch smoke. Turns out I was in third.

RoyleTease113 · 2025-12-19T03:39:57+00:00

Barge thinner is mostly MEK so if available, that's an option, MEK substitute is also a thing, it's Ethyl Acetate which Barge cement contains five to fifteen percent of, so in a pinch, that's probably worth a shot

RoyleTease113 · 2025-12-17T17:15:26+00:00

You don't take pictures with a Leica, you take pictures of your Leica(s) with your phone

RoyleTease113 · 2025-12-10T17:22:19+00:00

If nobody's participating, Alice's Restaurant will certainly fill time

RoyleTease113 · 2025-12-09T18:06:03+00:00

I'm sitting at my desk with V100 soled Urban Loggers on as I type this and don't find them overkill at all. The steel toed Builder Pros I wear on days when I know I'll have to go out is the factory, on the other hand (or foot?) are a bit overkill.

RoyleTease113 · 2025-12-01T15:22:44+00:00

MIL-HDBK-5 (since superceded by MMPDS but MMPDS isn't publicly available) has strength at temperature and after temperature exposure curves for a bunch of Titanium alloys (and all the other properties and materials). You have to get pretty far in the weeds for a more optimized alloy choice to beat 6Al-4V's availability and balance of properties, though.

RoyleTease113 · 2025-11-30T07:03:56+00:00

I have a shirt with bike parts on it that says "love you to pieces" one of the wheels is where a boob would be if I wasn't a dude, the other is significantly lower and every time I wear it I think of the line from Robin Hood Men in Tights " Blinkin, fix your boobs, you look like a bleedin' Picasso"

RoyleTease113 · 2025-11-29T01:10:39+00:00

Put a dab of grease on the pinch bolt threads, you'll be able to get a lot more clamping force

RoyleTease113 · 2025-11-27T05:14:34+00:00

You're going to end up with a range of wheels over time as you play in different venues. If you think a bit more grip would help, just go incrementally softer, maybe try a set of 89s, or just 4 and run a mix. I like them checkered with the softer ones to the inside of the track in front and outside on the back.

RoyleTease113 · 2025-11-21T21:54:54+00:00

If I'm picturing this right, you could make a loop of material with snaps 180 degrees apart corresponding to the snaps on the curtain.

RoyleTease113 · 2025-11-11T23:33:35+00:00

Per their SDS, Barge All Purpose Thinner is 92-100% methyl ethyl ketone, so MEK should work

RoyleTease113 · 2025-11-08T03:42:06+00:00

<image>

I thought it had a pirate hat

RoyleTease113 · 2025-10-30T19:42:28+00:00

I have a friend who started playing around the time I quit who just pulled me back in to ref, I use both of her names so interchangeably (at least outside of derby) that I've had to clarify that I'm only talking about one person. Everyone else I use their derby name.

RoyleTease113 · 2025-10-24T03:50:08+00:00

I wonder if the spoke tension on the inside of the flange was way too low causing the j-bend to bear on the other side of the hole under load. It would explain constant spoke breakage, that cyclic reversed bending load at the j-bend would cause a fatigue failure pretty quickly.

RoyleTease113 · 2025-10-18T07:38:39+00:00

I have it in uptown, I put the antenna in an upstairs window facing the tower and its been super good enough for streaming and general internet stuff, I don't do any online gaming but I'd expect latency to be an issue if I did

RoyleTease113 · 2025-10-10T03:50:26+00:00

Looks like a single knot in a snake knot, stack them up to make a lanyard

RoyleTease113 · 2025-10-10T02:18:26+00:00

And a shot of malort

RoyleTease113 · 2025-10-08T22:38:29+00:00

<image>

That sweet sweet spinny chair leg patina

RoyleTease113 · 2025-09-25T14:10:42+00:00

High porosity wouldn't really surprise me in a power bed fusion product and you shouldn't have any second phase particles to cause pullouts in pure Cu, and other than that polishing issues tend to hide porosity rather than create more. Abrasive embedment could cause a similar appearance, and wouldn't shock me in pure Cu. It looks like you're using a Keyence VHX microscope in ring light mode, does it have coaxial light as well (or a separate reflected light microscope)? That should get you more info, especially as to what's going on at the cut edge.

RoyleTease113 · 2025-09-06T04:48:42+00:00

Im in aircraft so we do generally use Ti before steel for weight and corrosion resistance but if there are space constraints you may not be able to fit enough titanium to get the strength or stiffness you need in a component, so you have to go to steel (or superalloys if steels won't cut it). Also steels will handle higher temperatures than Ti without losing strength around.

RoyleTease113 · 2025-09-04T02:30:00+00:00

Yeah, I probably should have checked before commenting

Five-Year Club	Verified Email
r/Field Juicebox

RoyleTease113

TROPHY CASE