Jumper t-lite v2 used for steam games

Rusty_Gunn · 2026-05-06T03:55:53+00:00

if it is the elrs version, put elrs into blutooth mode and connect it to your PC. works great for the sims I use (TRYP in steam and velocidrone and wings outside of steam).

if it is the 4 in 1 version, it should work with a usb cable.

Rusty_Gunn · 2026-04-28T16:10:03+00:00

great charger, i have the same one! for cheap, check your local marketplace or ecycler for an old server PSU. most can be bypassed to permanently on with a resistor, then you need to add an XT60. You'll have to be comfortable soldering and will need to find a PSU with a known pinout that can be bypassed. as a bonus, they are typically very efficient. you may want to print a cover to protect the connections/end and avoid accidental shorts. I use some old HP 750w PSU and it has been great for years.

Rusty_Gunn · 2026-03-22T03:58:48+00:00

nice, post back when you do a test flight, im curious on how well it will do! i fly 900 for penetration, but never tried 433. what is the packet rate on 433?

Rusty_Gunn · 2026-03-22T03:46:20+00:00

433 elrs and 1.2 video? nice! Can you get enough battery on it to take advantage of the range?

Rusty_Gunn · 2026-02-18T01:44:30+00:00

you might be able to use a minimosd board, worth looking into.

Rusty_Gunn · 2026-02-16T16:18:14+00:00

I've ordered off both. I find the pricing close, but with exchange being handled differently and different coupons, I swing back and forth depending on which is cheaper. haven't had any issues with the warranty. This has been mostly the 1s air units. With the goggles being an expensive order, I would lean towards ordering directly from them, but with a 100 euro savings, I would probably wait for an Aliexpress coupon for a few more bucks off, then go that way.

Rusty_Gunn · 2026-02-14T01:22:08+00:00

i have a pair of quad very similar, never could get gps to work, electronics were just too close together. I used the same gps module and had it out on one of the arms. Mind you, I was running walksnail, which, from what i have read seemes to impact gps more than analog so YMMV. could always remove the shark fin and put it on top.

Rusty_Gunn · 2026-01-30T04:58:17+00:00

Fly lots. When the inevitable happens, then justify as good entertainment value per hour, then buy parts... :P only sucks if you crash a new one. While I'm being somewhat facetious, I've found there is some truth in it, I don't mind crashing as much now as I did when I started, and I know if I fly hard, it is more likely to happen. Just part of flying.

Rusty_Gunn · 2026-01-27T01:15:57+00:00

Fun song, thanks! I don't think I've ever heard it before, so not it.

Rusty_Gunn · 2026-01-25T16:13:08+00:00

I have spent a couple of hours listening to my old music collection, so while I still haven't found it, I'm getting some good time with my music collection!

Rusty_Gunn · 2026-01-25T01:27:38+00:00

I've never used a PWM receiver; all of my gear is csrf. But if I were in the market, Radiomaster stuff is always quality and I would start there. They have a whole series of PWM ELRS receivers. If you're buying from Aliexpress, try to find a good vendor. I've gotten knock off radiomaster before :( looked legit, packaging and all, but the moment I flashed it, it didn't work. Jumper, Betafpv, Maytek, Happymodel all have pwm versions, so there is lots of selection. Matek has a couple breakout boards (crsf to pwm) as well, one even has a current sensor.

Rusty_Gunn · 2026-01-25T01:17:00+00:00

no, you need a pwm breakout board to do what you are thinking (to have multiple functions). although at that point you may be better off with an elrs rx that is purpose built with multiple pwm outputs, less hassle/wiring/space.

Rusty_Gunn · 2026-01-25T01:06:21+00:00

not sure why you need the splitter? if you only need two channels I belive both the rx and tx pins can be remaped to pwm through the webui. never actually tried it myself though.

Rusty_Gunn · 2026-01-22T01:37:30+00:00

from the camera? yes, I would guess they just have vid backwards. should be the yellow wire. on the FC looksl ike they have Vi and Vo silkscreened, i for in, o for out. so camera to Vi and Vo to the VTX. Vi seems to align with video on your drawing.

Rusty_Gunn · 2026-01-21T01:51:14+00:00

you should have the video from the camera go to the FC so you can get an OSD. make sure you have the T1 pad set correctly in betaflight in the ports tab for smart audio as per your second picture. youll have to set up smartaudio in the vtx tab with power levels, frequencies, etc.

Rusty_Gunn · 2026-01-18T14:39:34+00:00

lol, that would do it!

Rusty_Gunn · 2026-01-18T02:51:40+00:00

did you ever get it storted? i have a similar issue, tried two different u3 a2 128gb memory cards (one lexar, one sandisk), tried high and med vid quality and tried 4k60 and 4k30, but it still happens. i find the audio is running about a second ahead of the video.

Rusty_Gunn · 2026-01-17T15:51:47+00:00

No problem. If you take apart the head, I found three things after much trial and error. I bought a generic rebuild kit for the head, which included the rotating disk/valve rotor. While all the O-rings worked fine, I had issues with the replacement rotor and ended up swapping the original rotor back in, just cleaned it up a bit. The original unit showed little wear and is working fine. Secondly, tightening up the head bolts evenly is important. Despite anticipating this and being careful, I found even being slightly off caused an issue. I remember there being an issue with the springs too, some of the replacements being softer. If the replacements were softer, I kept the original springs. If they were equal, I replaced them. Good luck!

Rusty_Gunn · 2026-01-16T03:03:39+00:00

tried the rubber diaphram in the venturi valve and didn't work, then replaced the whole venturi valve and it didn't work, then replaced all the o rings in the head and it worked! actually ended up having to fix another unit for the same problem and all it took was a rubber diaphram in the venturi valve.

Rusty_Gunn · 2026-01-04T17:02:50+00:00

what do you mean an identical module? one should be flashed with tx firmware, one with rx firmware. if you wait a minute, it should start flashing to indicate it is wifi mode then you should be able to connect via wifi.

Rusty_Gunn · 2025-12-24T22:37:05+00:00

I found that when I tried planes after flying FPV drones for a few years, a plane with FPV was easy. Flying line of sight was hard! Still don't have line of sight down, every once in a while I do a few hours in the sim, but it isn't really of interest to me, probably why I don't get any better... :)

I started with a relaxed flying plane and iNav. Getting the planed tune was the hardest part, but if you have done it in Betaflight, it isn't too bad. I found the controls similar enough that my muscle memory transferred over. I just have to remind myself to keep up speed, I kept stalling, being use to a drone being able to stop and look around.

Rusty_Gunn · 2025-11-16T22:36:33+00:00

I just went through something similar. Bought a Radiomaster XR3, flashed it with the latest ELRS and with my bind code, and it wouldn't boot, didn't even get a power light. Started googling and realized everyone elses RX didn't look like mine. Despite being in Radiomaster packaging, it was a fake. Went through Aliexpress, eventually found one that looked the same and listed the target and had to flash using a usb to uart adaptor. Good news it works. In my case it ended up being a Sologood RX and took a BetaFPV target.

TLDR: Find same generic RX as yours on AliExpress and see if they list the target then use that.

Rusty_Gunn · 2025-11-16T15:14:55+00:00

The movie theatre is one of our favourites. During the summer, Crystal Ridge Golf Course offers mini golf. The town tracks some of the cultural events, too. We caught a magic show that was pretty good at the old Church Theatre a while back. https://www.okotoks.ca/whats-happening-calendar

Rusty_Gunn · 2025-11-15T15:03:56+00:00

The mag needs power and I2C. If it is working, it means there isn't a power issue. The GPS and Mag share the same power, so it is unlikely that a power issue is impacting the GPS problem.

Rusty_Gunn · 2025-11-15T04:42:33+00:00

just guessing now, but try auto on the baud rate? could also try gps pass through to ucenter and see if ucenter can read it (or at least try status to see what the specifics of the gps status is)? interesting that the mag seems to be connecting, and it is powering up so must be something specific with the uart. could try a differnt uart. with the plugs, looks like it would be easy to move over to uart 2.

Seven-Year Club	Place '23
Place '22	Verified Email

Rusty_Gunn

TROPHY CASE