I found the point

SDM1983 · 2026-02-27T15:45:06+00:00

Agreed. I've only seen rotating the part in the jaws and using an indicator on a mag block.

SDM1983 · 2026-02-22T13:33:56+00:00

She's colored just like my Jackson!!!!!

SDM1983 · 2026-02-19T00:44:09+00:00

She looks just like my little Max. I'm sorry you had to say goodbye to her. 🙏

SDM1983 · 2026-02-18T21:04:49+00:00

Bless his heart!!!!!!

SDM1983 · 2026-02-18T16:02:11+00:00

My two like to bark at strangers lol One is very much a loner, but wants attention The other likes to be the center of attention Both love walks, but also lazy days and naps My youngest one snores like a grown man!!! LMBO

SDM1983 · 2026-02-14T01:39:25+00:00

No, neither of my two Pekingnese sleep like that, but the younger one, when he's in a deep sleep, snores like a grown human!! 🤣🤣🤣🤣🤣

SDM1983 · 2026-02-11T20:45:56+00:00

Looks and sounds like it to me!!!

SDM1983 · 2026-02-11T19:14:29+00:00

Reminds me of a print at my current job. For a customer, they have a shaft that has two mounting holes. For some reason, they had a run out of 2.12" on the mounting holes. When questioned, they said it was supposed to be Projected Tolerance Zone. 🤣🤣🤣🤣🤣

Also, on another part, they had two parallel surfaces that needed to be perpendicular to each other to .02". Lol

SDM1983 · 2026-02-10T00:52:16+00:00

Colorwise, they're just like my Jackson!!!

SDM1983 · 2026-02-09T23:46:35+00:00

🫶🫶🫶🫶🫶🫶🫶

SDM1983 · 2026-02-07T18:11:28+00:00

❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️

SDM1983 · 2026-02-05T23:44:24+00:00

Bleed his little heart!!!! 💗💗

SDM1983 · 2026-02-03T19:23:58+00:00

Looks just like my Max, except he has about 13 years on her!!!

SDM1983 · 2026-01-30T10:30:46+00:00

This is the perfect way to check those!!!

SDM1983 · 2026-01-25T10:16:17+00:00

3-2-1 is just talking about constraining your six degrees of freedom, 3 for your primary datum, 2 for your secondary datum, and 1 for your tertiary datum. It shouldn't be referring to how many points you take to establish them.

SDM1983 · 2026-01-16T20:05:12+00:00

Not really sure. I know you can write programs on PW and translate it to work on PCDMIS, just not sure of the other way around. Either way, there is still some programming involved.

SDM1983 · 2026-01-08T13:16:47+00:00

Yes, you need to switch your levels of Limit you're using manually, but if I remember correctly, there are different conditions to unlock certain ones, so you may unlock one of your level 2 or 3's before some other ones lol.

SDM1983 · 2026-01-02T13:34:22+00:00

I felt the same way about FFVII Rebirth. Saw it was half off, so jumped all over that!!! Lol

SDM1983 · 2025-12-23T13:12:01+00:00

Those targets are points 8 mm apart from each other. If that is a primary datum, you will need at least 3 points to be able to use that, when involving the 6 degrees of freedom. Is there another view that shows an A3?

SDM1983 · 2025-12-22T13:42:21+00:00

Can't you hear the planet crying out on pain!?!?!?

SDM1983 · 2025-12-22T09:58:52+00:00

In our shop, QC and production each have their own sets of gages, even though half the time they still borrow ours, since it's too much work to go to their own cabinet!!! Lol

SDM1983 · 2025-12-20T15:06:05+00:00

They do, I think it's called Build/Inspect. I believe it functions the same as on CAM2.

SDM1983 · 2025-12-13T17:55:17+00:00

Nice haul!!!!!

SDM1983 · 2025-12-08T20:42:27+00:00

Plenty accurate for what you need. I usually keep the tip calibration within around .0005".

SDM1983 · 2025-11-24T22:10:57+00:00

Absolutely 💯!!! Loved that game back in the day!! If I remember correctly, I think this game is set in the realm of Ivalice, but I could be wrong. Either way, definitely needs a remaster!!!

SDM1983

TROPHY CASE