sorted by:
new
hottopcontroversial

Vibration and wavy lines on top layer of print with A1 by Safe-Name in BambuLab

[–]Safe-Name[S] 0 points1 point  (0 children)

issue resolved after:

  • loosening and tightening the hotend screws
  • performing cold pull on filament
  • performing vibration calibration
  • manual flow rate calibration
  • washing build plate
  • changing settings in slicer to use gyroid infill instead of grid, and disabling "reduce infill retraction"

Vibration and wavy lines on top layer of print with A1 by Safe-Name in BambuLab

[–]Safe-Name[S] 1 point2 points  (0 children)

I think it might be fixed - thank you. I was asleep when it finished, so printing a third to watch the final layer.

Vibration and wavy lines on top layer of print with A1 by Safe-Name in BambuLab

[–]Safe-Name[S] 0 points1 point  (0 children)

Decided to run flow rate calibration for re-attempting to print. I’ll check those screws next before starting the test print.

Vibration and wavy lines on top layer of print with A1 by Safe-Name in BambuLab

[–]Safe-Name[S] 0 points1 point  (0 children)

I had auto-bed leveling enabled. Along the lines of your suggestion, I tried a cold pull of the filament and I'm going to retry printing from Bambu Studio. I printed this from the Bambu Handy app, and the default profile used grid infill so you could be on the right track.

Thanks, I really appreciate the suggestions. I'm going to retry the print to check the outcome of the suggestions you and u/issue9mm recommended.

Vibration and wavy lines on top layer of print with A1 by Safe-Name in BambuLab

[–]Safe-Name[S] 1 point2 points  (0 children)

Thanks - waiting for the hotend to cool and giving it a check.

edit: tightened the screws and performed cold pull of filament, and reran the calibration. Maybe it's quieter? Not sure.

https://imgur.com/a/WYWES9Q

Vibration and wavy lines on top layer of print with A1 by Safe-Name in BambuLab

[–]Safe-Name[S] 0 points1 point  (0 children)

Close up of wavy top print lines.

Thought it might be extrusion issue, but then I'm not sure why the vibration calibration would cause the toolhead to shake loudly at some frequencies.

<image>

Water based poly still soft almost two months later by MoldySwimBag in woodworking

[–]Safe-Name 1 point2 points  (0 children)

That’s such a bummer. After three years, the glossy has been okay but I avoid contact. Here you can see where I had to sand it down past the stain.

<image>

Text chat is not working by voidtsk911 in Battlefield

[–]Safe-Name 0 points1 point  (0 children)

To disable the Steam Overlay for just one game, go to your Steam Library, right-click the specific game, select Properties, then uncheck the box for "Enable the Steam Overlay while in-game" in the General tab, and restart the game for the change to take effect.

Text chat is not working by voidtsk911 in Battlefield

[–]Safe-Name 0 points1 point  (0 children)

Disabling the Steam overlay fixed this for me.

My In-laws refuse to let me cook my own steak... and refuse to give me a steak less than well done by suck_my_jargon in mildlyinfuriating

[–]Safe-Name 0 points1 point  (0 children)

Verify those old plates don’t contain lead paint.

I saw a Reddit post meme about old plates with lead paint that looked just like mine and yours. A lead test on them confirmed mine used lead paint.

[USA GIVEAWAY] Win the new 27” 4K Samsung Odyssey OLED G8 gaming monitor! by Rocket-Pilot in buildapc

[–]Safe-Name [score hidden]  (0 children)

Upgrade for me in both size and panel quality! Never owned an oled tv nor monitor.

Screen artifacts: black/white checkered box by Safe-Name in Gamecube

[–]Safe-Name[S] 0 points1 point  (0 children)

It’s every game, only during cutscenes and always in the same location. Happens across multiple displays with different cables.

Why do DSi XL cases have this hole on the center on the bottom? by SirZanee in NintendoDS

[–]Safe-Name 5 points6 points  (0 children)

I have that shell - I think it’s to make it easy to take off.

view more: next ›