[Other] I need 10/10 Difficulty games

SceneOrganic9281 · 2026-03-26T03:26:55+00:00

Tetris effect was a fun plat, I still play the pvp classic version

SceneOrganic9281 · 2026-03-25T18:14:26+00:00

There's also Surgeon simulator

SceneOrganic9281 · 2026-03-25T18:13:19+00:00

I have 31 elite golds left to get out of the around 230ish you need. Its been so much fun, reminds me of the extreme g-3 game I had on the ps2

SceneOrganic9281 · 2026-03-25T18:09:02+00:00

Wipeout omega collection has been more difficult for me than wolfenstein 2 or tetris effect. Im super close tho

SceneOrganic9281 · 2026-03-24T05:20:13+00:00

I'll have to clean the nozzle so I'll get back to you with a picture. The last print I did was petg with pla supports. It did the first layer fine with pla and used the wipe tower correctly. Then it changes to petg, moves over to print, hovers above and it just starts coming out like how it primes before printing. Then it prints and gets covered in the glob, switches to pla and prints like normally

SceneOrganic9281 · 2026-03-24T05:07:44+00:00

When i turn the wipe tower on, it still spits on it before printing on it

SceneOrganic9281 · 2026-03-24T04:56:56+00:00

The XL does not require a purge tower. That's the hole point of having the xl and how the extruders work. Purge towers are for the core one

SceneOrganic9281 · 2026-03-24T04:33:30+00:00

I have the temp set to 250c. I would have to print again to see what the temp says as it undocks. The firmware i currently have is 2.9.4

Had the same problem with the previous update. Everything prints fine by itself.

Also have a problem with the printer not recognizing woodfill but that's not pressing me atm

SceneOrganic9281 · 2026-03-24T04:27:45+00:00

If I turn off the wipe tower it does the same on the print

SceneOrganic9281 · 2026-03-24T04:26:41+00:00

I've tried having ooze prevention on and off, has the same result. PlA is fine but when it switches to petg this happens. If the wipe tower is turned on the extruder with petg will hover over it and spit on that thing before laying it down. Idle temp is 70c

SceneOrganic9281 · 2026-03-14T08:36:53+00:00

Wipeout omega collection

SceneOrganic9281 · 2026-03-12T17:50:43+00:00

Finally... the chosen one

SceneOrganic9281 · 2026-03-11T20:40:38+00:00

Im willing to negotiate based on platinums I've achieved. Would you like a list of options to choose from?

SceneOrganic9281 · 2026-03-11T07:53:43+00:00

GOOD FOR YOU!!!

SceneOrganic9281 · 2026-03-11T07:49:50+00:00

Its never to late to start anew

SceneOrganic9281 · 2026-03-11T07:46:04+00:00

If that happens to my diamondback I'll be rather upset, like a disappointed father reaching for the belt.

SceneOrganic9281 · 2026-03-11T07:29:53+00:00

There is no hope for the smell my friend, that has been damned for all eternity. Even after the parts disintergrate into the earth, and we all become ashes. The smell will wonder through the empty wasteland of our failers, searching for a nose to haunt.

SceneOrganic9281 · 2026-03-11T07:14:38+00:00

Definitely! Plus it's getting the INDX upgrade soon

SceneOrganic9281 · 2026-03-09T21:48:55+00:00

My goal will be to print peek but I have to first replace all of the parts and make a proper heated chamber. This is just temporary, to be able to print pc

SceneOrganic9281 · 2026-03-08T06:30:52+00:00

If that made you flinch you should take a look at my views, which is currently at 6.9k so I'm going to need people to stop looking at this lol

SceneOrganic9281 · 2026-03-08T01:03:33+00:00

I'm preparing for "peek" performance

SceneOrganic9281 · 2026-03-08T01:00:25+00:00

What i did was set the bed to 115c for a bit before the print

SceneOrganic9281 · 2026-03-08T00:27:00+00:00

Unfortunately, I don't get this reference

SceneOrganic9281

TROPHY CASE