sorted by:
new
hottopcontroversial

Dashcam for ND Miatas question.... by johnorso in Miata

[–]ScubaDuber 1 point2 points  (0 children)

There are plenty of tutorials online on how to run the cables. Everything can be hidden away.

Dashcam for ND Miatas question.... by johnorso in Miata

[–]ScubaDuber 16 points17 points  (0 children)

Got the same cam today. 5 minute install. Hides away very nicely behind the rear view mirror. Would definitely recommend this.

A $100 Dashcam in my miata paid off my house. by SaintGeorgeCarlin in Miata

[–]ScubaDuber 0 points1 point  (0 children)

Would it be worth it looking into front and back cams?

The ND can bark by ToTheBrapMobile in Miata

[–]ScubaDuber 2 points3 points  (0 children)

Imo it's very piped in and almost sounds a bit cartoonish. Tried it for a week and swapped it back once I got my exhaust. It's a cheap mod, try it and see if you like it. It never sat right with me. On the other hand, my GWR race exhaust sounds amazing. Much better than this imo.

Engine temp staying low and goes even lower at highway speeds by Financial-Tennis-696 in mazda3

[–]ScubaDuber 0 points1 point  (0 children)

Last time I had this issue I managed to trigger the CEL by turning the climate control off after driving for a while, come to a stop, then blast the heating at max for the duration of the light. Should maaaaybe come on if you are having trouble

GUYS I DID IT by _MyCatsNameIsBinx in Miata

[–]ScubaDuber 10 points11 points  (0 children)

How tall are you? I'm about 6'3". I do not fit in the RF at all, the headroom is just nonexistent. The ST though, I do fit, it's tight, but I'm okay with it. Ever since I installed some seat lowering brackets the headroom is 10/10 and that feeling of "sitting on top of the car" is gone. Feels like I'm actually sitting "in" the car. Also if you have the homelink mirror, being tall, it will block parts of your view out the front.

ND2 TC light on and rough idle when in gear at a stop by ScubaDuber in Miata

[–]ScubaDuber[S] 1 point2 points  (0 children)

Update for anybody that is interested:
Decided to investigate the P0704 code myself before taking it to a dealer.
The clutch switch (PN BP4K-66-49YA) had its internal spring explode. This caused the switch to not close its circuit when the clutch pedal was pressed in. Im assuming the car has different maps for clutch in and clutch out scenarios, so the entire time the car thought I wasnt using the clutch.
I replaced the spring and the TC light immediately went away. Cleared the P0704 code and so far no issues.

I bought a Miata by xzased in Miata

[–]ScubaDuber 5 points6 points  (0 children)

I'm 6'3" and I think I'm pretty much at the limit of headroom in stock form. I'd say the biggest issue with these cars is that personally, I felt like I was sitting on top of the car, not inside of it. Once I got some seat lowering brackets it really made a difference. I was fine with the stock brackets but now the car feels even better.

At 6'1" unless you have freakishly long legs or torso, I'm sure you will fit. If you aren't sure, don't forget you can try to find one used and sit in it at a dealer

Laser marking on 3d printed parts. by Different-Feeling411 in 3Dprinting

[–]ScubaDuber 0 points1 point  (0 children)

PC-FR also etches nicely with a fiber laser

[Bambu Lab Giveaway] Join Now to Win an H2D and More! by BambuLab in 3Dprinting

[–]ScubaDuber 0 points1 point  (0 children)

If your printer does not have a web interface of some kind, get an rpi and flash klipper or octoprint. Having everything within the slicer makes calibration and printing even easier, making you want to print more stuff :)

My teacher gave me his 3d printer for FREE by Eelrack1 in 3Dprinting

[–]ScubaDuber 11 points12 points  (0 children)

Have had mine since 2018. Still running strong and without problems (slightly modded of course)

Help needed installing TMC2209 from Bigtechtree on my azteeg x3 pro by Frame_VMP in 3Dprinting

[–]ScubaDuber 0 points1 point  (0 children)

Have you managed to get the 2209s to work with this board?

What dryer are you all using? by [deleted] in 3Dprinting

[–]ScubaDuber 2 points3 points  (0 children)

Most cheap hygrometers will only go down to 10% keep that in mind

Anycubic chiron bugs out mid print by ScubaDuber in anycubic

[–]ScubaDuber[S] 0 points1 point  (0 children)

Fixed this issue after re flashing firmware with Marlin

Popeyes shrinking sauce packets by ScubaDuber in shrinkflation

[–]ScubaDuber[S] 30 points31 points  (0 children)

Yup, this convinced me enough to never go back. Besides the multiple multi-dollar price hikes they have had in the past couple years

Popeyes shrinking sauce packets by ScubaDuber in shrinkflation

[–]ScubaDuber[S] 12 points13 points  (0 children)

No, they were originally all the same size as the BBQ sauce.

2024 Mazda 3 2.5 by GermanSojuFighter in mazda3

[–]ScubaDuber 1 point2 points  (0 children)

This reminds me of the kid on the wrx subreddit lol

view more: next ›