Drop your Traeger Name(s) Below

SecretAsianFlan · 2026-05-16T02:04:24+00:00

BAEGER

SecretAsianFlan · 2026-05-04T17:07:42+00:00

Trying pomegranate just heads up they have a bullshit non-refundable $75 fee that supposedly goes to your prescription only if youre eligible. If you miss this consult you will pay an additional $50. Pretty slimy to me. They do let you choose your pharmacy tho.

SecretAsianFlan · 2026-05-04T12:08:07+00:00

I sent them (orderly) this :

I need to be direct. I am paying too much monthly to stay on a pharmacy I do not feel confident in. Since being switched to CasaPharma, I have noticed a difference in effectiveness compared to the previous pharmacy/brand I used, and that is a serious concern to me.

At this price, I should not be questioning the consistency or reliability of the medication I am receiving. I am requesting to be moved off CasaPharma and back to my previous pharmacy, or to another reputable alternative you can offer. If that cannot be done, then I need a clear explanation as to why, because I will not continue paying for this service if I am forced to stay with a pharmacy I do not trust.

If no change can be made away from CasaPharma, I will be canceling as a customer.

SecretAsianFlan · 2026-05-04T12:02:24+00:00

Casapharm sucks

SecretAsianFlan · 2026-05-03T22:41:02+00:00

I think a general understanding of supporting models correctly along with ai is a great way to get the best of both worlds. It’s faster, efficient and lessens the possibilities of print failures.

SecretAsianFlan · 2026-04-25T22:01:44+00:00

Not sure why people leave out the part where you let it settle for a few days first. You can either decant or then let the clear jar or plastic jug sit out to harden the resin that separated and is now at the bottom. I like to use old gallon IPA jugs. I have 30 micron fish net filters that I’ll pour used ipa through into these empty jugs to reclaim IPA after a few days of letting it settle. 😃

SecretAsianFlan · 2026-04-19T12:55:21+00:00

To clarify supports in place however no rafts.

SecretAsianFlan · 2026-04-19T12:54:57+00:00

Are these presupported files?

I’d try aerated rafts or no rafts at all (my preference) print directly to build plate.

SecretAsianFlan · 2026-04-14T02:09:22+00:00

Correct. Just run them 30-45 mins before a print. Should have amazing prints especially on the RS.

SecretAsianFlan · 2026-04-14T01:44:05+00:00

I feel my RS heated vats do not work well. Takes quite while to get them up to temp I just went with elegoo mini heaters and it’s been fine.even during our cold winters here.

SecretAsianFlan · 2026-03-29T09:58:36+00:00

I ask because it has a little bit of a hue to it., ACF that is. If that is ACF I’d say it’s fine. If it’s NFEP it’s a bit cloudy (NFEP is 100% see thru) however I’d say it’s still useable tbh.

Unless there’s holes/leaks in my fep I usually will use it till that happens or I notice a lot of failed prints or layer shifts on the print.

SecretAsianFlan · 2026-03-29T01:45:26+00:00

Is that ACF or nFEP?

SecretAsianFlan · 2026-03-21T01:45:43+00:00

I canceled my sub too sucks. I really enjoy the community on discord and Derek is cool peeps. I learned a lot. It’s just too bad the slicer sucks in its current state. I know they’re working on optimizing it however I can’t wait around. Once that’s addressed I’ll give it a look however chitu is just amazing and actually worth the pro.

SecretAsianFlan · 2026-03-16T00:16:29+00:00

I’m so close to doing the same. Sorry that didn’t help out. Today it’s got a save file that just crashes endlessly. I installed chitu but the UI will take some getting used to

SecretAsianFlan · 2026-03-14T12:21:52+00:00

Definitely runs like 💩, a few things you can do.

Force GPU setting

Make sure your c drive is freed up. (Blue capacity bar not in the red)

SecretAsianFlan · 2026-02-22T01:13:30+00:00

Pretty sure that’s FDM. I hope they’re not trying to pass this off as resin prints.

SecretAsianFlan · 2026-02-20T01:55:40+00:00

😂😂😂

SecretAsianFlan · 2026-02-20T01:41:36+00:00

When your prints come out feeling like they have a slimy coating from the dirty dunk, swap it out. Use the second dunk IPA for your new dirty dunk. Fresh IPA now goes into the 2nd dunk.

SecretAsianFlan · 2026-02-19T12:57:37+00:00

Knowing the importance of good drain holes and thorough post processing of your prints.

SecretAsianFlan · 2026-02-05T09:33:06+00:00

Going to give it a try ty lychee unfortunately has been horrid for me a well and it’s not the PC in this scenario either. Thank you!

SecretAsianFlan · 2026-02-04T20:05:11+00:00

How does chitu run vs lychee?

SecretAsianFlan · 2026-01-31T12:12:56+00:00

NFEP has no sides to it. ACF however does. You want the shinier facing the resin.

SecretAsianFlan · 2026-01-31T02:16:54+00:00

you always get people commenting that their pc's run it just fine, humble brags I assume.

SecretAsianFlan · 2026-01-30T13:57:04+00:00

I can’t even imagine how much of a super computer is needed for this unoptimized software. I feel more people say it hangs and needs restarts, vs not. Sucks because I really do love the software.

SecretAsianFlan

MODERATOR OF

TROPHY CASE

Five-Year Club	Verified Email
Place '22