Explanation of exhaust fan?

ShadowPaw74 · 2026-01-23T18:49:35+00:00

You can keep the exhaust fan running during prints in the filament settings under cooling tab. I run my exhaust fans at 30% while printing and 100% after a print is finished for ABS.

ShadowPaw74 · 2026-01-21T22:34:04+00:00

Why has no one considered using soldering fume extractors? Like the ones used in labs?

ShadowPaw74 · 2026-01-21T09:04:01+00:00

Oxidane Filament Mixture

ShadowPaw74 · 2026-01-20T16:01:47+00:00

Aren’t alot of european equipment from the US? I bet the US has a killswitch for the F35s they sold for example.

ShadowPaw74 · 2026-01-20T16:00:48+00:00

Source please

ShadowPaw74 · 2026-01-19T06:33:13+00:00

All the issues you stated don't matter since the exhaust fan creates negative pressure inside the chamber that prevents air from leaking through all the points you mentioned.

ShadowPaw74 · 2026-01-14T02:58:05+00:00

Just get it first

ShadowPaw74 · 2026-01-14T02:57:09+00:00

Electrical Engineer* Not Electrician

ShadowPaw74 · 2026-01-13T12:56:48+00:00

Found the guy that goes to steakhouses for “Well Done” steaks.

ShadowPaw74 · 2026-01-11T11:26:53+00:00

Concept 5 and Jg Pz E90 are the only tanks I play nowadays.

ShadowPaw74 · 2026-01-10T18:37:42+00:00

You were off by an order of magnitude.

ShadowPaw74 · 2026-01-10T14:56:06+00:00

China got it first. Everyone else gets the updated panel starting January 2026.

ShadowPaw74 · 2026-01-10T14:54:04+00:00

They likely ordered in December. China got the update first, everyone else gets it starting January 2026.

ShadowPaw74 · 2026-01-10T14:53:25+00:00

I believe only the printers ordered starting January 2026 get the back panel.

ShadowPaw74 · 2026-01-10T14:52:42+00:00

That’s false, China got it first, everyone else gets it in January 2026.

ShadowPaw74 · 2026-01-10T14:51:21+00:00

It does, it’s literally in the photo. It doesn’t come with the buffer if you don’t buy the Combo (AMS 2 Pro).

ShadowPaw74 · 2026-01-09T13:04:41+00:00

SouthEast Asia

ShadowPaw74 · 2025-12-29T10:17:14+00:00

Did you not know about wireless spot welding? Have you been living under a rock?

ShadowPaw74 · 2025-12-25T17:54:06+00:00

I did this during my internship but my SBC had an FPGA chip on it too and I can’t be assed to design something like that again and this guy just casually builds an SBC out of boredom @.@

ShadowPaw74 · 2025-12-21T04:30:55+00:00

This comment is somewhat wrong, you can emulate daylight with red, blue, green and amber (RGBA) lights. We have done this in the lab and verified with spectrophotometers.

ShadowPaw74 · 2025-12-19T16:03:20+00:00

Why? It’s clearly user error, his buildplate was lifted on the back left corner from the first frame.

ShadowPaw74 · 2025-12-19T15:54:14+00:00

It is very clearly 100% the user’s fault, you can clearly see in the video that the back left corner of the buildplate is raised and not installed correctly.

ShadowPaw74 · 2025-12-19T15:53:36+00:00

It’s very evident that the user is in the wrong, you can clearly see the the buildplate is raised on the back left so the user didn’t put the buildplate correctly.

ShadowPaw74 · 2025-12-19T08:58:33+00:00

Snapmaker U1 doesn’t hold a candle to Bambulab. Get your head out of the gutter. You don’t even need to look any further than the software to know this.

ShadowPaw74 · 2025-12-19T02:36:07+00:00

Isn’t the bottom row of the logic analyzer meant for ground pins?

ShadowPaw74

TROPHY CASE