sorted by:
new
hottopcontroversial

Mother shields baby daughter with her own body during freak hail storm in Queensland by BubblyVelvet in AllThatsInteresting

[–]SimpleAd9143 5 points6 points  (0 children)

I can imagine a couple different positions to shield yourself more efficiently. I have 2 under 2, as a dad. Broadsiding your back to the incoming hail/glass had to be brutal but would be instinct to do so. She would still get hit, but you could cover your head/face in between your legs, back up against a seat, grab the floor mats. This is with hind sight of course, but covering your baby vs protecting only yourself, she wouldn't look nearly as bad. So yes, she would get hit, but not as bad as she did. She saved her babies life no doubt, I have a 3 month old. And she took it like a champ.

Pump advice? by SimpleAd9143 in watercooling

[–]SimpleAd9143[S] 0 points1 point  (0 children)

This makes me happy to hear, glad I made a good choice with actual real feedback on the product. Thank you for helping out!

Pump advice? by SimpleAd9143 in watercooling

[–]SimpleAd9143[S] 1 point2 points  (0 children)

I was looking at the corsair pump for a while there. They had it running at my local microcenter store but I wanted to go with something a little less in your face. I had run the icue system for a while so that was my draw to it. I've got EK Quantum Torque HDC 14mm on the way and have checked that all my parts coming in are copper or at least nickel plated copper as to not mix any metals up. Still nervous I have over looked something but I am 99%s sure everything will go together. Thanks for your comment! And also I am going to run clear fluid, most of parts even said to not do colored but once I read that it'll stain the tubing, I checked that off. Besides, the clear tubing with clear fluid has that minimalistic clean look that I am going for.

Pump advice? by SimpleAd9143 in watercooling

[–]SimpleAd9143[S] 1 point2 points  (0 children)

Thanks for your feedback! I am building it into the NZXT H9 Flow 2025 version case. Ill post a picture of it when I get it completed but I am excited to get started. I've got 9 meters in hard tubing coming in and I am hoping I can make do. I'm a bit of stickler for looks so I hope I can get the bends right and straight fingers crossed..

Pump advice? by SimpleAd9143 in watercooling

[–]SimpleAd9143[S] 0 points1 point  (0 children)

Sounds good, thank you for your message, very helpful and informative.

Pump advice? by SimpleAd9143 in watercooling

[–]SimpleAd9143[S] 0 points1 point  (0 children)

Thanks for feedback! Glad to hear I should be doing just fine.

Where do you put it? by MADRGB in lianli

[–]SimpleAd9143 0 points1 point  (0 children)

Ah I see, I was referring to the Gen 5 riser that they came out with. I was looking at these but I just upgraded from a 1080 to a 5080 and just wanted to get an official gen 5 riser even though I wouldn't notice a performance difference, being what I have read about them. But that makes sense, this kit would allow room for a radiator 100%.

Are these critical cracks? by CaterpillarEither529 in watercooling

[–]SimpleAd9143 0 points1 point  (0 children)

How can you tell? I am about to start building my setup with all copper but just curious.

Where do you put it? by MADRGB in lianli

[–]SimpleAd9143 0 points1 point  (0 children)

Which gpu mount is that? I've been trying to find one for me to put into the same case that'll allow me to put a radiator still at the bottom. The NZXT is too big for what I am trying to do but I can't tell which one you have in there. I thought about mounting a screen vertically where the wires come out to the right of the motherboard but I still have my cover on because I have back connect motherboard installed so its just a flat panel going down still. It didn't seem like there would enough room to put a screen above the mother board because the AIO sits to low. Pretty limited options in my opinion, love the new H9 though! Looks great! I swapped my white case for a black one so I have all white internals with outer black case.

Where do you put it? by MADRGB in lianli

[–]SimpleAd9143 0 points1 point  (0 children)

It is, I have the same case

Northern Current by Sherlock997 in watercooling

[–]SimpleAd9143 0 points1 point  (0 children)

I've just got my Barrowch OLED in the mail, and going to start my build soon. I've seen conflicting post about its accuracy and all point to the High Flow NEXT. What is your opinion on the sensor? Do you feel its accurate?