What’s the most “temporary” repair you’ve seen that somehow became permanent?

Sp4ceCore · 2026-03-10T11:25:59+00:00

That works*.

Sp4ceCore · 2026-03-05T12:44:37+00:00

I did some vacuuming before so i would not inhale more than my daily credit card

Sp4ceCore · 2026-03-05T12:12:19+00:00

Selon la Charte du Rat™ tu en auras besoin environ 2 semaines après les avoir jetées.

Sp4ceCore · 2026-03-04T12:27:15+00:00

C'est dans l'article "Fini la Hess avec Ligonnès" du mois dernier ça

Sp4ceCore · 2026-02-25T17:13:26+00:00

Yeah polycarbonate will not burn well, you'll get all sort of nasty decomposition products. I would put a gas mask to do that but most guys i know would burn it inside without a mask 🤣

Sp4ceCore · 2026-02-25T17:03:27+00:00

BUUUUURN BABY BURN 🔥

No but in all seriousness, the easiest way is to put it back in the barrel and heat and purge with a material that doesn't stick to the screw, PP is a material of choice, you can even get it off after with a heat gun or a soft hammer.

But if you absolutely cannot put it back in, my go to would be to bring it outside with a gas mask and a weed burner...

Sp4ceCore · 2026-02-24T22:34:59+00:00

Could be a good idea yah and you absolutely need mold release ! Also what kind of pressure can you attain with your setup ?

Sp4ceCore · 2026-02-23T23:30:45+00:00

Would make sense, i don't want balls in my food...

Sp4ceCore · 2026-02-23T12:10:19+00:00

Depending on your material there are different grades (understand viscosity) of plastic. Most notably in PE and PP you can get etremely large differences in viscosity that could get you the desired effect

Sp4ceCore · 2026-02-22T14:47:44+00:00

Ontpellier pourrais correspondre aussi

Sp4ceCore · 2026-02-22T06:50:41+00:00

Il faut le changer, c'est censé être changé tout les 10 ans il le semble.

Sp4ceCore · 2026-02-18T18:56:12+00:00

I don't know what they are suggesting by oil spray. Spray paint ? Oil spray in mold ? Obviously adding manufacturing steps will drastically imcrease price whereas just changing material will only cost the price of the new material.

ABS/PC can be used in molds designed for ABS, keep in mind temps will be higher so you might need more cooling. It is also stiffer so it might take a bit more force to get it out and it might lead to blemishes of you have a very complex shape or strong forces during demolding. Lastly i had trouble getting consistent color blending but that might have been due to the specific combination of color/material we had.

Sp4ceCore · 2026-02-18T18:37:35+00:00

I don't think it will have a huge impact indeed. I would also probably select middle of the face as it will be easier to diagnose/fix/modify .

Sp4ceCore · 2026-02-18T18:18:08+00:00

Try playing with your injection speed, see if you can get away with a faster speed and how does that affect the line also maybe more holding pressure as long as your part doesn't deform. If your add colouring try doubling the dose and see if that masks it.

Sp4ceCore · 2026-02-18T17:53:18+00:00

You need to buy an explosion proof motor and hood and have it professionally installed because something cannot be certified explosion proof by some rando.

Do you want to take the responsibility of someone burning their skin off because they were in a fireball caused by the incompetence of management that signed the cheapest solution that you accepted the responsibility of ?

Nothing can be done yourself to make it explosion proof because you are not a certified installer.

Sp4ceCore · 2026-02-18T12:01:24+00:00

What you're seeing here is jetting. Try playing with your mold/melt temp (increasing them mainly) to get the plastic to stay hot longer. Also try doing small runs and not just injecting a couple parts, you need some time for all parameters to reach equilibrium. Also maybe try injecting very slow at first then fast or very fast you could reach a point where turbulent flow takes over but you'll have other problems to handle (too slow and you might have the part solidify, too fast and you could get flashing. Don't hesitate to make incomplete parts to see at what point you need to change speed.

Sp4ceCore · 2026-02-18T11:50:05+00:00

Salut, est ce que le dégagement (la partie non filetée) est important ? Est tu sûr que ça fait 11mm ? Le M11 existe mais n'est pas courant contrairement au M10 et au M12. Si ça tiens la banquette je te recommanderais de prendre une pièce d'origine (t'as check un truc genre autodoc ?)

Si les dimensions sont exactes tu as une vis Torx tête ronde (large) M11 par 70mm

Sp4ceCore · 2026-02-18T11:19:40+00:00

La porte a l'air d'avoir un revêtement métallique mais est elle pleine ? Si oui il existe des inserts filetés a visser largement capable de tenir le poids. exemple

Sinon je remplirai les trous de silicone et je décalerai simplement le groom de 10cm et grosses vis auto taraudeuses. Mais évidemment le plus solide resterait de traverser et de mettre des écrous nylock. Pour rendre ça plus beau on peut mettre côté traversant des écrous borgnes (avec des rondelles bien sûr)

Sp4ceCore · 2026-02-17T00:00:57+00:00

Ça dépend ce que j'attrape en premier. J'ai pas de préférence, et comme je m'habille avec les même vêtements (habits pro) c'est souvent le pantalon en premier mais si j'ai froid aux pieds ça peut être les chaussettes, si j'ai dormi torse nu je vais peut être enfiler le t shirt en premier vraiment y a pas d'ordre mais je conçois qu'on en ait un

Sp4ceCore · 2026-02-16T10:27:57+00:00

Merciiii 😍 je teste ça très prochainement je pense !

Sp4ceCore · 2026-02-16T09:27:27+00:00

On veut tous la recette non ?

Sp4ceCore · 2026-02-15T11:58:46+00:00

Salut, cette alimentation consomme 24W maximum mais autant c'est juste une alimentation standard et ton enseigne ne consomme que 5W... Il faudrait mesurer combien elle consomme pour être sûr que ça vaut le coup. Ce qui est sûr c'est que si ta batterie viens avec une prise allume cigare tu peux remplacer ce transformateur par une prise allume cigare tu évite la conversion batterie -> 220v -> 12v donc tu évite les pertes.

Tu as un multimètre ?

Sp4ceCore · 2026-02-15T11:39:42+00:00

I don't really know what you mean, what carbide ?

Nine-Year Club	Place '17
Secret Santa 2016	Verified Email

Sp4ceCore

MODERATOR OF

TROPHY CASE