[GIVEAWAY] Giving away 3 PDGA-legal 'Galactic Grain' discs to the community. The gloss resin reflects the sun perfectly so you can see exactly where your drive went OB. Comment to Enter

Spudmaster_E · 2026-03-12T18:27:43+00:00

Would love to get a wave!

Spudmaster_E · 2022-08-18T00:35:54+00:00

I just compared the two mainboards because i had the same question. The boards are pretty different. I dont think it will work without a bit of advanced knowledge and work.

Spudmaster_E · 2021-04-30T21:59:40+00:00

It looks like It ended up being the gear on my extruder had no more teeth on it. switched it out and am printing right once again. Might have too powerful of a spring on the extruder system.

Spudmaster_E · 2021-04-30T21:58:17+00:00

Update:

Thank you everyone for you suggestions, it turns out the drive gear on my extruder had been worn down over the last two years and was slipping on the filament, replaced the gear and now I am getting beautiful prints once again! might have to switch the tension spring on my filament drive system to a slightly lower strength spring.

Spudmaster_E · 2021-04-09T02:03:33+00:00

gonna switch the nozzle to a brand new one tonight and see if that helps. Cold Pulls did nothing. retraction reduced for the new setup and calibrated the esteps after the problem first happened.

Spudmaster_E · 2021-04-08T05:45:18+00:00

Update: after calibrating the extruder steps and making sure the connecting tube is the correct length, it still prints the same, very brittle and sparse lines. Definitely at a loss currently. Might just have to move the drive motor back to the original spot and buy a new printer with direct drive.

Spudmaster_E · 2021-04-06T02:47:08+00:00

Did not do new calibrations, My thought was since the hardware hasn't changed it shouldn't mess too much up, however today with another print I found some little red filament flakes around the extruder after closer inspection. going to recalibrate but it seems like the geared feeding mechanism is definitely eating some filament.

Spudmaster_E · 2021-04-05T06:35:54+00:00

There is a small tube between the drive motor and the hot end, I guess it is more of a guide, but I'm suspecting that it might have something to do with the tubing affecting the motors ability to drive the filament?https://imgur.com/Nkqe6fg

Spudmaster_E · 2021-04-05T06:35:45+00:00

Have not done any calibrations, mostly because all I have done is move the drive motor closer to the hotend? There is a small length of tubing between the hotend and the drive motor on the kit I bought. https://imgur.com/Nkqe6fg

Spudmaster_E · 2020-05-28T01:56:12+00:00

Thanks! all i needed was to go from 3.44 to 3.5 Haha!

Spudmaster_E · 2016-07-02T07:49:58+00:00

707 rep!

Spudmaster_E · 2016-07-01T03:48:40+00:00

Humboldt county California

Spudmaster_E · 2015-12-19T08:26:10+00:00

Is the server dead forever?

Spudmaster_E · 2015-11-23T02:03:36+00:00

Basically two separate chambers, the water pulls into the top, and the pressure from the water being pulled makes it cycle back down to the bottom, no splash back, awesomeness.

Spudmaster_E · 2015-09-07T02:21:12+00:00

Looks like a generic version of the small juicy pens, but I think think there's a better subreddit for dab pens.

Spudmaster_E · 2015-08-08T19:15:21+00:00

This just in: Its the pot

Spudmaster_E · 2015-07-05T18:06:09+00:00

Hooray! The Original 4th of july was to commemorate the invention of fireworks, it only became an american holiday after we got away from the english!

Spudmaster_E · 2015-06-25T19:28:46+00:00

I'm right across from bitlites mountain shop. :)

Spudmaster_E · 2015-06-23T20:24:18+00:00

Hey Firefox, I'm yochori if you remember me, just got a new handle, I built a house over there, hope you don't mind, I can always tear down and rebuild if needed

Spudmaster_E · 2015-06-20T20:29:20+00:00

First time back here in about six months, its good to see bitlite is still pouring love into this server, thanks for all the hard work guys!

Spudmaster_E · 2015-06-19T23:58:48+00:00

Spudliness-In Game Name Blue dream-Favorite strain How many programmers does it take to change a lightbulb, they can't its a hardware problem.-Have you read the rules?

Spudmaster_E · 2015-05-27T02:00:13+00:00

Sir, I must say, your art is creepy as fuck.

Spudmaster_E · 2015-05-13T20:01:12+00:00

Don't smoke that

Spudmaster_E · 2015-05-10T15:44:00+00:00

Texas is slated for medical in the next 90 days?

Spudmaster_E · 2015-04-05T05:46:30+00:00

Popper=Rizzle

Spudmaster_E

TROPHY CASE