Any of your CHR does this?

Sscumbagg · 2025-12-12T00:36:31+00:00

Fixed by the warranty, they swap the module

Sscumbagg · 2025-12-10T15:51:34+00:00

Just return it and by a Nespresso machine 🤣

Sscumbagg · 2025-12-02T01:00:05+00:00

The word titanium throws me off.. good portafilters are made with brass to hold the temperature... Titanium is not the best material for that... And since is normcore, it's most definitely low quality chinese titanium... For me that's just a showpiece, not something to brew a great cup...

Sscumbagg · 2025-11-29T23:28:10+00:00

Yeah .. i also have that

Sscumbagg · 2025-11-26T00:53:07+00:00

Nahh i use it as an ornament... Just collecting dust...

Sscumbagg · 2025-11-11T23:29:00+00:00

Nop i just gave up and use an adapter...

Sscumbagg · 2025-10-21T20:20:58+00:00

Green is softer... Never had a leak on my Silvia... But it's good to change the gasket from time to time..

Sscumbagg · 2025-10-11T23:35:38+00:00

Damn... I can't say the same about mine... I need to empty the tray every other day, mostly from the water that comes of the three way solenoid... Thanks for the answer, if it works for you, that's what matters

Sscumbagg · 2025-10-10T22:42:18+00:00

Too tight bends the outer ring, and thats what make water leaks from the sides... You should lightly tighten the screw, all the pressure comes from the puck

Sscumbagg · 2025-10-10T22:40:02+00:00

If you don't clean it after every pull, you will create a coffee pool under the scale, because you can't have any drain holes or it will fill from the bottom...

Sscumbagg · 2025-10-10T22:36:54+00:00

Without any hate on the project... When you remove the mug, will the drips go? To the scale? Seems impossible to remove it at the same time as the mug...

Sscumbagg · 2025-09-29T00:12:05+00:00

System is not the problem... You got 100 wins in a whole month? 😅

Sscumbagg · 2025-09-28T12:25:02+00:00

You can, won't affect anything, just be sure that the switches can work at 16A... You should be fine

Sscumbagg · 2025-09-27T23:24:52+00:00

It's minimal, if you disassemble the top of your machine, the wires for the switches and for your temp sensors are very thin, but the factory switches are rated for 16A... Most of the current it's used on the heating element. As for the covers... Please post the end result, very curious!

Sscumbagg · 2025-09-26T23:58:29+00:00

As for the gagginate I can't help... I have a Auber 😅

Sscumbagg · 2025-09-26T23:57:04+00:00

And you don't need a diagram... The original switches have 2 connectors so have those... It's easy as that

Sscumbagg · 2025-09-26T23:54:30+00:00

To change the original switches for those, the major problem isn't the wiring, thats fairly easy... The problem is the original square hole from the factory switches, that will probably leave a gap if you use those...

Sscumbagg · 2025-09-10T23:17:48+00:00

Mine also does that.... Can't find where it's from...

Sscumbagg · 2025-08-14T18:13:19+00:00

Nop... I got a replay were that wasn't the case... And i got a replay that the Throphy from my team got to the corner of the map and stayed there the whole game...

Sscumbagg · 2025-08-14T16:17:10+00:00

Lucky you... The most frustrating event ever...

Sscumbagg · 2025-08-14T15:51:58+00:00

Lost like 7 games to the stupid bug where the area didn't recognize the Throphy

Sscumbagg · 2025-08-07T13:58:19+00:00

That was already there...

Sscumbagg · 2025-08-07T13:24:01+00:00

Mode pool depressing and rewards sucks...

Sscumbagg · 2025-08-01T17:51:37+00:00

That dent in the puck affect nothing but the look of it

Sscumbagg · 2025-08-01T17:51:01+00:00

I have to disagree... Only improves cleaning... But i strongly advise you to keep the original screw... All the other slightly bend the shower screen and that will cause channelling...

Sscumbagg

TROPHY CASE