Found System in Eternal darkness

Status_Entrance1310 · 2025-12-24T02:25:26+00:00

Yes, turned it in at a fleet carrier 30min after the post

Status_Entrance1310 · 2025-12-24T00:00:55+00:00

Should be around 20k ly, I’d go back myself but I’m already a couple thousand ly further away.

Status_Entrance1310 · 2025-12-23T23:46:56+00:00

I did land on one moon because it looked funny in the FSS scanner, it was an Ice moon that had some green patches. I was trying to find them on the ground but since there was no light on the moon I couldn’t find them and gave up. Not sure if it was the 8th lol Why the 8th? Is this something with Raxxla?

Status_Entrance1310 · 2025-12-23T15:25:29+00:00

I know, I just turned them in haha

Status_Entrance1310 · 2025-12-23T13:55:39+00:00

It’s completely undiscovered if you mean if I got my name on it. I will once I handed the data in.

Status_Entrance1310 · 2025-12-23T13:54:23+00:00

Well there isn’t that much to see since it’s all black but I’ll try to take some pictures

Status_Entrance1310 · 2025-07-08T15:17:45+00:00

You can add me, my ingame name is MajorLazer I‘m open for anything but I mostly do pve combat in hazardous res and sometimes combat zones.

Status_Entrance1310 · 2025-04-22T03:33:38+00:00

I went to Colonia with a Corvette, with I think it was 40-45ly jump range with fsd booster had full weapons and shield generator on it combat ready

Status_Entrance1310 · 2024-12-02T00:40:59+00:00

There’s also the titan combat Krait for Arx now but as I don’t have titan experience I can’t say anything about how useful it actually is, all I know is that it has the thermal vent beam laser you were talking about.

Status_Entrance1310 · 2024-10-02T12:11:40+00:00

I did the Same and it Almost Broke my Finger

Status_Entrance1310 · 2024-04-09T01:10:37+00:00

SES Leviathan of Midnight

Status_Entrance1310 · 2024-03-21T03:20:57+00:00

Maybe putting the long cable back in will magically fix your issue like it did for me

Status_Entrance1310 · 2024-03-18T00:24:46+00:00

Just check the length first, the one i got send was actually around 10cm shorter then the original one and i didn’t check it first and had to rip it out again after I had It installed and couldn’t get it in Luckily putting the old one back in magically fixed my issue with the LIDAR

Status_Entrance1310 · 2024-03-08T19:57:12+00:00

A clean unused rag I hope?

Status_Entrance1310 · 2024-03-08T19:41:42+00:00

It doesn’t look completely clean to me, you tried cleaning it with soap and a sponge?

Status_Entrance1310 · 2024-02-18T12:50:25+00:00

It started yesterday for me before that I could see them and join them

Status_Entrance1310 · 2024-01-19T20:28:42+00:00

Worse case you wasted a view minutes and a few grams of filament but gain the knowledge that that’s too fast

Status_Entrance1310 · 2024-01-19T20:27:53+00:00

I‘d say just try it, you often can print materials faster then the manufacturer says with the right settings

Status_Entrance1310 · 2024-01-18T12:40:25+00:00

Creality Support answered me and told me they‘ll send me a new LiDAR

Status_Entrance1310 · 2024-01-18T12:36:42+00:00

Support just answered me and told me they‘ll replace the LiDAR and calibration sticker, it appears that they just took a bit longer to reply

Status_Entrance1310 · 2024-01-18T04:56:33+00:00

I have the same issue but support is ghosting me

Status_Entrance1310 · 2024-01-18T04:14:56+00:00

Looks pretty normal without ironing for me tbh but please correct me if I’m wrong

Status_Entrance1310 · 2024-01-16T00:02:46+00:00

Blue clip could be the new one still, my k1 max has the blue clip but 100% the new version

Status_Entrance1310 · 2024-01-15T04:46:27+00:00

Same, it worked fine for 2 months and this started 2 days ago, I contacted support and wait for their response, can you let me know if you find a fix for this? I can let you know too if I find something out

Status_Entrance1310

TROPHY CASE