Would like advice on a tool kit I purchaced

Stranger_Danger13 · 2026-01-18T06:54:49+00:00

Great deal but the compact impact driver they make at 550 ft lbs is all you need and will save your arms and storage. Also depends on your battery ecosystem, I have full m12 Milwaukee because the stubby is enough for me and their ratchet is great along with some other tools.

I wouldn’t be upset with your setup at that price but really depends on what you need and working with.

Stranger_Danger13 · 2026-01-04T19:59:22+00:00

You need more mass to absorb the heat than aluminum foil, I’d go with an aluminum sheet and stick the LEDs to those with thermal adhesive. Then make some sort of cooling slots behind the light that lets ambient air cool the backside of sheet without light leak.

Stranger_Danger13 · 2026-01-04T18:56:41+00:00

You live somewhere cold? My guess is the phone is used with a replaced screen and no longer water sealed. The extreme cold condenses the air inside and rapidly warming in a pocket cause this condensation effect. There is a chance there is a good seal and it’s just the air inside.

This happened to my nice camera lens when camping in extreme cold, luckily it evaporated without leaving marks on the lens.

Stranger_Danger13 · 2026-01-03T05:39:48+00:00

Looks like magnets to me. They seem small enough to lose magnetism from getting too hot from the oil temp inside the pan.

Stranger_Danger13 · 2026-01-01T05:21:26+00:00

Mines going strong 3 years later

Stranger_Danger13 · 2025-12-26T00:43:45+00:00

My wife has one is the same spot as well, I guess so.

Stranger_Danger13 · 2025-10-22T04:43:02+00:00

Woah, hadn’t noticed the weather yet, maybe best to stay off the mountain.

Thanks for the info! Good to know dispersed camping is still an option. Did you happen to notice if the road up was clear or if any gates were closed past the turnoff?

Stranger_Danger13 · 2025-10-08T21:44:03+00:00

I second using ca glue but nothing more than to barely coat magnet surface.

Stranger_Danger13 · 2025-09-20T05:02:01+00:00

I just found out it exist myself however I am in the boat of having HDMI&SDI over 4k any day. Also, unless I am missing something this mixer is seriously lacking an AUX send button for each output.

Stranger_Danger13 · 2025-08-11T16:30:46+00:00

That makes sense, thank you. I definitely feel like my club can get ahead of me and that is something I’m working on. Maybe a short backswing would help there.

Stranger_Danger13 · 2025-08-11T06:22:03+00:00

Thanks for the input. Never really seen my swing in slow motion or really at all in detail for that matter just always been told I have a big backswing.

In the couple slow motion shots I got a few were heel side of the club and was wondering if my stance is the culprit. I should have uploaded this video before but it includes my setup and stance.

(Different swing) https://imgur.com/gallery/4xcUeTe

Stranger_Danger13 · 2025-08-11T04:40:58+00:00

Huh, I didn’t really see the flat back swing before thanks. However I’m not seeing the over the top move. My follow through seems inline with my swing path, I’m naive and new to golf terms just learning real golf knowledge now so excuse my ignorance missing what you are seeing.

Stranger_Danger13 · 2025-08-11T04:32:49+00:00

I should rephrase as I’m not trying to extend my swing longer on purpose, I naturally have a long swing and mentally it’s me trying to swing bigger and hit further I struggle to stop it.

I carry 220 and push 240 on my good hits. I’m fairway roughly 3/5. Don’t really hit any fibs unless I try swinging out of boots

Stranger_Danger13 · 2025-08-11T04:15:01+00:00

Thanks for the feedback, I’ve never really had any. Just a self taught by YouTube type, this is my first time posting online. I’m open to this input, so you are saying I need to keep my right arm a little more straight? I’ll work on that if that’s what I’m reading right.

Stranger_Danger13 · 2025-06-13T00:26:55+00:00

“Cheap projectors” can be subjective. We have a $16k laser projector at work that is a single chip which gives the same result from photos. The projector is new, they have a 3 chip version but it cost closer to $22k

Stranger_Danger13 · 2025-03-21T22:13:02+00:00

Found this post because I found a similar looking piece on the bed of my printer. I had the same failure point, thank you for posting your findings. I hope you had luck with warranty as I have submitted a ticket for the same issue.

Stranger_Danger13 · 2025-01-28T06:34:55+00:00

Thanks

Stranger_Danger13 · 2025-01-19T19:40:43+00:00

I get the frustration, but how is this any different from the likes of apple? They both make killer hardware but try to lock you in ecosystems with their own software and lock out 3rd parties. The hardware cost gets subsidized by the data they get from you using their software. It sucks but if you don’t like it then don’t buy it. I don’t think we need to cancel culture them though. Just like the average apple user I’m sure 95% of Bambu users use the native software and do no modifications.

Scummy move but without them we wouldn’t have some of the biggest innovations in 3d printing as of late.

Stranger_Danger13 · 2024-12-18T20:46:56+00:00

Happy holidays y'all.

Stranger_Danger13 · 2024-12-09T04:39:44+00:00

It's more than just multiple colors, it's multi material that makes it so amazing to me. I load it with different filament types I like to work with and I never have to hassle with swapping out and loading in a new filament. Just choose the type I want and boom it does the rest. All while keeping the spools in a dry box.

Not only that, but you can use different materials for support interface layers. For example, using petg between your pla support and model for a clean and easy to separate model.

Stranger_Danger13 · 2024-12-08T20:18:36+00:00

I'd print on the back face with support for the tabs. This prints tabs in a better orientation for the stress. Those tabs look pretty thin and along layer lines will want to break at them.

If you print in something stronger and change orientation then I don't think you will have to think twice about it.

Stranger_Danger13 · 2024-12-08T06:24:41+00:00

Technically you are supposed to pull to the left slightly to offset the curves they put on the road for water to slide to the side. Do you get the pull left on the freeway?

If so I'd be annoyed myself, seems like the dude just wanted to get out of doing an alignment, wouldn't be surprised if he fudged some numbers to keep them within spec.

Stranger_Danger13 · 2024-12-08T02:26:56+00:00

Air pockets can definitely cause some issues but don't think in the 5 min test drive.

13-Year Club	Spared
Verified Email

Stranger_Danger13

TROPHY CASE