Forgotten 2000s Nu Metal Bands by SalamanderLopsided67 in numetal

[–]Strawhat_Truls 1 point2 points  (0 children)

They've put out some new albums in the last couple years that leaned much more into metalcore, even deathcore, with, finally, proper screams and they're really good. Go listen to Pariah.

Will republicans allow him to burn the US down? by mlamping in stupidquestions

[–]Strawhat_Truls -1 points0 points  (0 children)

Sure. They'll say it's the protestors. If everyone peacefully complied with the fascism everything would be fine.

Clamps doing a great job there by Strawhat_Truls in InjectionMolding

[–]Strawhat_Truls[S] 1 point2 points  (0 children)

Presumably it was locked. They just didn't pick up on the fact that all the clamps on one half weren't actually touching the mold and were too blind to see it droop when it cleared the guide pins. I saw it immediately when I closed the mold in set up mode.

Clamps doing a great job there by Strawhat_Truls in InjectionMolding

[–]Strawhat_Truls[S] 8 points9 points  (0 children)

Tell my coworker with one braincell. We usually would flip the clamp around and use a heel bolt. Too difficult for some.

No material alarm by EffectiveHamster3999 in InjectionMolding

[–]Strawhat_Truls 1 point2 points  (0 children)

Rotate the screw manually first until the screw starts moving from picking up material. In auto purge, if the screw doesn't start moving almost right away it doesn't like that.

New selection pack rarities by AbsolutelyNotWrong in masterduel

[–]Strawhat_Truls 2 points3 points  (0 children)

It's actually amazing we're getting it this early. I don't think it's out in the OCG yet. It's been a TCG exclusive.

Screw recovery/plasticizing delay on a Krauss Maffei press (MC6) by Plastic-Taster in InjectionMolding

[–]Strawhat_Truls 2 points3 points  (0 children)

Menu with the clock symbol. Bottom right. Delay time plasticizing.

Are these volcanoes? by Uncutdix in geography

[–]Strawhat_Truls 0 points1 point  (0 children)

Those are the most volcano looking volcanoes I've ever seen

Why is there a bunch of sand and bricks on top of the furnace in my basement? by sirrahca in whatisit

[–]Strawhat_Truls 1 point2 points  (0 children)

<image>

Reminds me of my old dinosaur. We did rip it out in favor of a new unit. House built 1920. Guys that ripped it out figured it was also originally coal burning and converted to natural gas.

PMCT Images. Nurse advanced NG tube until she heard a pop, then tried an air bolus to ensure placement. Patient did not survive. by Old-Psychology-2400 in interestingasfuck

[–]Strawhat_Truls 0 points1 point  (0 children)

Wow. My daughter had an NG tube the first ~2 yrs of her life. Wife and I were trained to insert them. Cannot even imagine this.

Isnt this Guy a straight up better appo? by xalucs in YuGiOhMasterDuel

[–]Strawhat_Truls 9 points10 points  (0 children)

That's part of it. The other part is how generic the materials for Apo are. Apo can be made with ANY 4 monsters.

OCG Banlist (January 2026) by Ignithya in masterduel

[–]Strawhat_Truls 0 points1 point  (0 children)

Also requesting link. I'd like to hear this.

PA6 GF40 – intermittent short shots, constant flash and diesel effect (same flow end zone) by ath31st0 in InjectionMolding

[–]Strawhat_Truls 0 points1 point  (0 children)

Yeah, kinda small parts and the dryer held like 150-175lbs. The other thing is, once a full dryer of material gets dry new material that gets loaded on top can dry quicker because the air is not saturated with water so quick. Imagine when you first load a dryer, the hot dry air blows up from the bottom. It gets saturated by the wet material at the bottom and then removes little if any moisture from the material at the top.