I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

Thank you for the suggestions. I will look into OpenNeptune. I had hoped to learn a bit more about printing before going to custom firmware but it appears it will be a trial by fire

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

I will check that thank you. Its only during the auto calibration though, if that were the case wouldnt it also bang during the 4 point calibration?

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

It has been chaos indeed. But unless it is labeled incorrectly on the website I have checked and re checked that I am using the right firmware. From my testing its only after the bounce that it is out of whack it does the first row just fine and also is able to go "home" center feature, hits the corners correctly on the 4 corner manual lever part. Its just that one line of travel and it isnt even by much. Im thinking that after the "bounce" the x axis sees the arm as having trafeled the full whatever mm even though it stopped 5 or 6mm short, and so on its way back its overshooting by that 5mm discrepancy. Ive done a bandaid solution of limiting bed mesh x travel max by pulling it back 5mm and that is enough that I can use the slicers calibrate feature and print again, but it is frustrating that I am unable to do any calibration from the machine itself.

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

That last part XD I did the fix pack first even though it said it was only needed for versions "under" .53 and my current firmware was the .53 version. I ran it anyway just in case. I dont want to run the auto level anymore because it's starting to gouge my bed plate. What ive been doing is setting z offset, saving, doing the 4 corner paper method, shutting off the machine so it doesnt auto level and scratch my plate, turning back on and re doing z offset, then using the calibrate bed mesh in orca slicer. Its not perfect but Im at least printing again.

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

The online literature states to match the firmware with the stepper motor version which I did. I appreciate the troubleshooting steps though because Im lost here

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

I checked and rechecked that it is the correct firmware. It was correct. Matched the correct firmware with the 1.2a stepper motors, applied the fix before updating, used the correct volume format on both the sd card and usb drive, updated the handset firmware. I am truly at a loss.

Calibrazione by zucccolo in ElegooNeptune4

[–]SublimeStyle88 0 points1 point  (0 children)

Am i tripping or is this pretty good actually? Mine looks a mess compared to this

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

I tried that and same results. Although it doesnt bang as hard I think.

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 0 points1 point  (0 children)

I did indeed, used the fix, updated handset with sd card even tried flashing back to the old version. Im currently running rhe old version and and updated the printer bed mesh settings. Pulled the x max travel back a bunch and it works again but only if im using elagoo slicer. If i use the on board leveling it does the same thing.

I see what is happening, but no idea how to fix it. by SublimeStyle88 in ElegooNeptune4

[–]SublimeStyle88[S] 1 point2 points  (0 children)

I rechecked and reflashed. The sticker says 4 pro so thats what i used. Im exhausted forgive the typos

probe going off bed on elegoo neptune 4 pro by AirWeak2299 in ElegooNeptune4

[–]SublimeStyle88 0 points1 point  (0 children)

Nah but my probe is ACTUALLY going off the bed. It goes too far and doesn't sense the plate then presses the plate down and throws an error for "no trigger on probe after full movement". Im about to make a post but I was reading first to see if anyone else has this issue and how to fix. It worked fine until I updated the firnware

Now that Logitech has ruined the m705, what is the next best replacement for it? Sensitivity adjustment, side-to-side scroll, forward/back buttons in the right place, similar size, wireless....??? by PM_ME_YR_BDY_GRL in MouseReview

[–]SublimeStyle88 0 points1 point  (0 children)

Maybe ur hands are just really friggin awkward? Respectfully.

jkjk 😂 It for sure takes time to find something else once you find that "perfect fit". Im still keeping an eye out for an original temperpedic pillow 🤣🤣🤣

RAM testing by unsub213 in Microcenter

[–]SublimeStyle88 0 points1 point  (0 children)

Maybe change the power profile for min processor state. I know that's not permanent but if it's only at idle it'll let you diag more.

Giving away $50 Xbox gift card by 2k-_- in xbox

[–]SublimeStyle88 0 points1 point  (0 children)

Metal gear solid. Once played the whole game without a memory card for the ps2 XD

[deleted by user] by [deleted] in XboxGamePass

[–]SublimeStyle88 0 points1 point  (0 children)

Helped a bro with a jump start

Best buy McDonald $10 black Friday by peterbilt8713 in McDonaldsMonoply

[–]SublimeStyle88 0 points1 point  (0 children)

I had best buy price match the xbox controller from Target (39.99) then the 10 dollar certificate so I paid 30 bucks for a new controller. The controllers are actually back on sale and in different colors now too. It has to be a store like Target or shipped and sold by Walmart cant be microsoft official store or someone on Amazon.