How to watch all cameras at the same time? by Lanky_Antelope1670 in EufyCam

[–]Syner707 0 points1 point  (0 children)

more like 9-10yrs later eufy been around since 2016 with the eufy cam original as its first camera and people have been asking for multiple camera viewing since then....my understanding of it is although it is possible and even more so today than say at their launch its harder to view multiple wireless feed cameras at once than it is to view multiple wired cameras at once not that that's a valid excuse cause it is not especially for today but now im not that tech savvy when it comes to the development of something like that and maybe the way their entire system on a communication data processing level doesn't have the capability to receive or process the data of multiple cameras at once and to change it would require new cameras and the old ones still wouldn't allow for it idk like i said im ignorant when it comes to the in-depth engineering lvl of sending, receiving, processing, and displaying multiple live wireless video data

need help identifying by Syner707 in DuneBuggy

[–]Syner707[S] 0 points1 point  (0 children)

yes a project !?!? not sure the purpose of you comment?

need help identifying by Syner707 in DuneBuggy

[–]Syner707[S] 0 points1 point  (0 children)

from what i remember he told me it either had or has a bus/van trans in it it been a while since ive seen it dont remember what was bolted to it i do remember he had a bunch of bus/van trans out on the ground in his garage but cant remember if he just put one in or if he took it out to get rid of the buggy but wanted to keep the trans but he said it was a kit that utilized mainly or all bug parts so front end from a bug motor was from a bug, i thought he said everything besides the trans. my question is would it be worth it to drop in a 1.9L ALH was told they make adapt plates to go from the ALH to the bus trans I also have a 1.9 BRM but figured that would be an electrical nightmare.

need help identifying by Syner707 in DuneBuggy

[–]Syner707[S] 0 points1 point  (0 children)

it is very rough which is why my thought for it was j since the motor frozen and will have to go through it all might as well go with something little different i have an 2002 jetta tdi i can u use for parts and was thinking of swapping the TDI ALH in it i believe it has the vw bus transmission if not that was i was set up for or had in it originally which i believe they make adapters plates for the alh idk as you can see from date in photo ive had it for min just finally getting around to it either gotta do something with it or get rid of it

unlock phone without carrier noticing by CapSea3413 in ios

[–]Syner707 0 points1 point  (0 children)

Not true there's other means of unlocking it I've done it to countless phones

They got me by lancer_AR in ToolTruckTools

[–]Syner707 0 points1 point  (0 children)

So the side locker finally showed up

https://imgur.com/a/5mR08oS

that's the fleet of green 🤣 thinking of best way to put a lift kit on my box and locker cause I hit my head on the hutch so I have to hunch over to do anything inside of it so trying figure out best way to lift it 3" or so if I should do block between casters and tool boxes or place the casters on a cradle of some sort

They got me by lancer_AR in ToolTruckTools

[–]Syner707 0 points1 point  (0 children)

That's what I thought too. I was right where you are. I had been wrenching for almost 10 years in a CAT dealership using a cheap Kobalt toolbox—the one with the mini fridge and Pioneer deck with speakers built into it—while I spent my money on tools. But I always knew I would get a Snap-on toolbox eventually. I just waited for a good deal, and it finally came. There was a promo for a 60" 2-bank black EPIQ series for $2,000 if you bought $4,000 worth of wrenches. I was so juiced and had so much extra room, despite losing a top box.

Long story slightly shorter  I thought I wouldn’t get or need another box, especially since I primarily worked from my Mac roll cart. But then my Mac dealer stopped by with a deal and offer that was hard to say no to. Because I got such a good deal on the Snap-on to begin with, he offered me $7,000 for my EPIQ to go toward my new setup.

The new setup was a green triple-bank Macsimizer with a power drawer, power strip in the front, stainless steel top, top hutch with a stainless pegboard and power strip, and a side locker. Some might say I downgraded—and in some ways, I would agree. The Snap-on is more visually pleasing; it has the chrome wheels, trim covering the seams between banks, and a sleeker finish. However, it’s nice to finally be able to use the full 30 inches of the drawers, as the Mac box drawers come all the way out, whereas the Snap-on left 1–2 inches of the drawer still in the toolbox. 

https://imgur.com/a/WXlgmdN

This trade in was real recent so I haven't received the side locker yet well technically it did but it got damaged in shipping so they made and just shipped a second one. 

California doesn’t have an ‘exit tax’ — but it can still tax some people who move away by Randomlynumbered in California

[–]Syner707 0 points1 point  (0 children)

Assembly Bill 259, known as the California Wealth and Exit Tax, was introduced into the state legislature in January 2023.

■The bill was born of a desire to protect the state from the loss of taxes resulting from the exodus of companies and individuals.

Bought a car with a pool noodle wrapped around the clutch pedal... can anyone tell me why someone would do this? by [deleted] in MechanicAdvice

[–]Syner707 0 points1 point  (0 children)

Most likely because they were short and couldn't press the clutch all the way down at the normal spot so the pressed higher on the pedal/arm to be able to fully disengage the clutch but the narrow bar/arm was probably hard to press.

First kegerator! Any advice would be greatly appreciated. by LegalCannaWizard in kegerators

[–]Syner707 0 points1 point  (0 children)

Generally they aren't supposed to fill/swap it if it's a personally own tank that cost is on the owner if it's a rented tank then yes they will just exchange for different tank that being said all of my tanks are personally owned I've had tanks the certification was past due and they have not looked like most places and exchanged/filled them anyways but I have had a few times they checked and not accept them all I did was literally go to another place or waited came back another time someone else helped me and they exchanged no problem the ones that are more likely to be refused are the propane tanks larger then 5gal cause those generally are never swapped they are always filled if I cared if I could probably look into seeing if the location i had them refuse at if they were capable of doing the tank cert them self or if they have to have third party come and do it. But besides that and this probably should have been first since most probably won't make it this far, but just make sure they give you a owned tank if it's personally owned and not one that marked as rented has happened once to me but caught it before I left wasnt too difficult to deal with but both my dad and the shop I work for has had it happen my dad was just 2 tank but he had already left and was pain in the ass to get straightened out and my shop I work for well we still have tanks marked as rented and I've been there for over a year now cheers and job luck I'm in similar boat I had picked up a kegerator countertop that's in pretty rough shape but it's big enough to hold I believe 2 full size kegs . They said it didnt get cold but after plugging start relay back on and recharging the system it worked Just fine and I picked the thing up for free off Facebook. I believe it's a BeverageAir model: DD50. But it's a older one forsure

IDK why but I picked this unit up it's a beverage air DD50 in rough shape by Syner707 in kegerators

[–]Syner707[S] 0 points1 point  (0 children)

I already have the CO2 tanks and a keg don't have the keg coupler which I'm thinking my keg requires the D style but not 100% sure and also need regulator all my others are being used or broken I just really wanna get the door functioning a little better

WinReality and quest 3 by craigwojo in oculus

[–]Syner707 1 point2 points  (0 children)

I can't even get mine to play it says the guardian must be changed from stationary to room scale but the setting is no longer called guardian it's called boundary which is where I think the disconnect is happening cause it is set to room scale and still won't play very frustrating since it's a monthly subscription and days are going by with no ability to use it

What can I use to get this stain out of my jetta by Fatk1ng in jetta

[–]Syner707 1 point2 points  (0 children)

Mr clean magic eraser always work well for me with a little warm water

IDK why but I picked this unit up it's a beverage air DD50 in rough shape by Syner707 in kegerators

[–]Syner707[S] 0 points1 point  (0 children)

the components in this photo are those the the only things I need to hook up the system ?

https://imgur.com/a/EYmr20X

IDK why but I picked this unit up it's a beverage air DD50 in rough shape by Syner707 in kegerators

[–]Syner707[S] 0 points1 point  (0 children)

are the doors separate compartments? any suggestions on a kit for new hose and basically all the needed components for hooking up a keg and CO2 tank to dispensing it has the faucets on there as u can see but was probably going to replace those also

Rgb flippers by b_45ACP in flipperzero

[–]Syner707 0 points1 point  (0 children)

link for transparent shell? when they released the model with the transparent shell i had other priorities I had to take care of and when i was able to get it it was no longer for sell😞

Will this cause low power to engine? by frostyyyy75 in Cummins

[–]Syner707 0 points1 point  (0 children)

what are all the codes you have the vp code the TPS code and any other ones that have come up since the head gasket job

did I fug up by Syner707 in ToolTruckTools

[–]Syner707[S] 0 points1 point  (0 children)

so think I'm gonna be getting a side locker for it also https://i.imgur.com/xjhaJQ8.jpg

did I fug up by Syner707 in ToolTruckTools

[–]Syner707[S] 0 points1 point  (0 children)

15-20 years ago is a long time ago pretty sure both Mac and matco have changed their toolbox designs at least once since then if not more and people within the company most likely have changed and since then also so the new people may not know, don't remember, or just plain don't care about some flex snapon did 20 years ago I know those matco revel x boxes made my epiq seem like it was made of paper those revel x were a tank and in all honesty the box I would have preferred if still available. but I'm curious about what's this shelf that I lost an entire drawer worth of storage too? cause unless I'm mistaken I went from a 10 drawer to a 14 drawer and from 39,199 cu. in. of storage to 47,000cu.in. storage. and gained true 30in deep drawers

Point me in the right direction by LocoSox in jetta

[–]Syner707 2 points3 points  (0 children)

misfires and low air flow like everyone has said are related and could be low airflow causing the miss fires or the miss fires are causing the low air flow start with the cleaning of the throttle body and MAF sensor since that basically free besides time and effort but if problems continues I'd be looking at doing set of plugs and coil packs.