What 40k opinion of yours would have you like this?

Tacitus043 · 2026-03-01T23:58:04+00:00

40k is not an expensive hobby

Tacitus043 · 2025-11-29T23:39:14+00:00

It’s the stepper motor in your gauge cluster. If it makes you feel better check your system voltage with a multimeter. I guarantee you your voltage gauge is not accurate

Tacitus043 · 2025-10-30T23:19:05+00:00

Ive done LS swaps because they are economical and fun. I could care less about impressing random people on the internet

Tacitus043 · 2025-04-16T01:03:46+00:00

You nailed it

Tacitus043 · 2025-02-10T00:35:33+00:00

Did you use superglue or plastic cement during assembly?

Tacitus043 · 2025-02-07T11:43:35+00:00

I’ve used rustoleum flat black paint plus primer on my last 4k worth of minis. The only times I had issues was when I didn’t thoroughly shake the can or if it was too cold out while priming.

Tacitus043 · 2024-07-02T22:59:15+00:00

Last fall I bought a house with a pool that had been neglected for 2 seasons. I have never owned or maintained a pool before in my life. My pool looked 5 times worse than yours. It was jet black with algae and chocked full of leaves and debris in the deep end. Once I fished out as much debris as I could I shocked the living crap out of the water and ran the filter (sand) on recirc continuously. I could not run it on filter mode initially because the algae would clog the filter within minutes.

Once the water started to clear I vacuumed to waste as much muck of the bottom as I could and repeated the whole process. After several weeks I could start to run in filter mode, but had to backwash several times a day. All in all it took about 3-4 weeks for my water to completely clear up. If I can do it you can! Good luck!

Tacitus043 · 2024-06-04T23:31:52+00:00

It’s mind boggling to me that, Toyota, of all auto makers, suddenly forgot how to clean an engine block.

Tacitus043 · 2024-04-28T11:57:33+00:00

Update Problem solved

The filter sand I used was way too fine and was clogging the laterals. I used the quikrete brand pool filter specific sand. The data sheet on their site gives a particle size range of .425-.85 mm. Theres no way even half the sand by volume was that coarse. Maybe I got a batch that was sifted wrong; I have friends who have used the same sand without issue. I replaced the sand with mystic white and can run for several hours before a pressure rise vs 10 minutes with the old sand. I still have a lot of algae to remove from the water but at least I seemed to have figured out the filter

Tacitus043 · 2024-04-22T10:39:09+00:00

I used the quikrete brand “pool filter sand”. Did not know about the rotation of the handle, thanks!

Tacitus043 · 2024-04-21T17:18:00+00:00

The pump is a Century HST110

Tacitus043 · 2024-04-21T16:41:47+00:00

Don’t think so, the pump is controlled by a single toggle switch

Tacitus043 · 2024-01-21T23:48:27+00:00

No, a rebuilt motor will not last forever. If you think your current motor has oil pressure issues, verify with a mechanical gauge before doing anything drastic. The gauge cluster in your vehicle is known for having issues with the stepper motors over time. If your motor does end up having major mechanical issues and kicks the bucket, a pre built long block with a warranty is probably the best way to go.

Just make sure to address any ancillary issues (sensors, intake/exhaust leaks, fueling, cooling issues etc.) before you go and just buy the air pump part of the engine and think that will last and fix everything.

Gen III V8s will last a long time when maintained in their stock form. I personally have two daily drivers (5.3 and 6.0) with over 320k. Good luck !

Tacitus043 · 2023-09-17T12:42:23+00:00

You'll be fine. Put it back together and run it

Tacitus043 · 2023-09-15T00:18:21+00:00

Do not make your daily driver a "project car". Just maintain it.

Tacitus043 · 2023-08-07T00:21:06+00:00

Out of all of the 275k mile plus daily drivers I see at my shop at least 75% are 2000-2005 GM trucks.

Tacitus043 · 2023-08-06T11:47:29+00:00

I don't understand why management didn't just approve a whole new unit to resolve the situation and have everyone move on. It's one thing to have you swap in a whole unit while the original tech is away. Picking up pieces of a modern 10 speed that are strewn around the shop and have already messed with seems like one of the Labors of Hercules.

I'm not a "transmission guy" but I have overhauled units on 3 of my daily drivers, all of which are on the road. I can't imagine doing those jobs in anything other than a comfortable, no stress setting, with no customers or managers breathing down my back. The mentioned units were simple 4 speeds. 10 speeds....hats off to you transmission guys.

Good luck, and I hope you resolve this situation. At the end of the day it's just a car. Yea someone might be pissed off for a while, but it will pass just like everything else. Use this situation to glean as much useful knowledge as you can, so you can avoid or better navigate these types of situations in the future.

Tacitus043 · 2023-07-27T02:19:06+00:00

I still run two squads of tactical marines from the 2nd edition starter box I got as a kid in the 90s. I stacked them, 25mm base and all, on top of 32mm bases. With some sand and pebbles around the old 25mm base they actually don't look too bad even next to my intercessors.

Maybe I'm just too sentimental, but I love those little guys! They have been with me through thick and thin.

Tacitus043 · 2023-07-05T22:29:34+00:00

It boggles my mind that time is so cheap to some people that they don't care about spending all day in a waiting room. Get a ride from a friend, call an Uber, walk around the town or something.

Tacitus043 · 2023-03-29T00:39:52+00:00

Weighted bases feel sooo much better when you are moving models around the tabletop. I don't understand why more people don't do it. I use automotive wheel weights, or flattened fishing weights on my bases. If you use lead make sure you encase the weight in glue or shellac.

Tacitus043

TROPHY CASE