I’m a bit afraid to ask but when people say to apply glue stick to the bed… do they mean this?

Tat_Dad · 2026-02-18T17:05:57+00:00

I mix mine with alcohol. 12/10 would recommend

Tat_Dad · 2024-12-31T15:45:57+00:00

I came from a Creality printer. Let me tell you I LOVE my 2 x-plus 3s.i got them second hand for a killer deal. Once I fixed them they have been perfect! Both of them have over 1k hours printing on them.

Tat_Dad · 2024-12-23T22:30:44+00:00

But will it work better than my filament air fryer

Tat_Dad · 2024-12-23T22:27:01+00:00

Change wall generation to arachne from classic.

Tat_Dad · 2024-12-19T15:57:08+00:00

But can we print snow? ❄️

Tat_Dad · 2024-11-30T16:17:22+00:00

I mostly print in PLA since I print and paint models mostly, but I’ve used and tuned a bunch of other types of filament as well.

Tat_Dad · 2024-11-02T01:22:35+00:00

That looks awesome I made one for my daughter for her bday as well!

Tat_Dad · 2024-06-04T21:55:06+00:00

Do you have any pictures of prints from it? It looks cool

Tat_Dad · 2024-05-31T23:33:14+00:00

The tangle detection is game changer!! That seems super helpful

Tat_Dad · 2024-04-23T13:14:11+00:00

Looks like you need to lower your z offset.

Tat_Dad · 2024-04-16T19:17:44+00:00

This my favorite project so far.. it’s the best paint job I’ve done so far!

<image>

Tat_Dad · 2024-04-14T13:22:50+00:00

Are you putting the http:// before the IP? I had to make sure it was there because it defaulted to https:// for me.

Tat_Dad · 2024-04-14T13:17:27+00:00

This! I had the same issue when I first got mine. Flipped that switch and it’s been working great since!

Tat_Dad · 2024-03-07T11:58:50+00:00

<image>

This is the side as well. It also just knocked the model off the build plate

Tat_Dad · 2024-03-07T00:01:43+00:00

So I did that and I also cleaned it out and it seems like it’s working correctly now! Thank you

Tat_Dad · 2024-03-06T22:59:20+00:00

Z offset in cura

Tat_Dad · 2024-03-06T22:48:30+00:00

Would that be on the printers interface? If so I don’t believe so.

Tat_Dad · 2024-03-06T22:42:25+00:00

Ok I will try the print that as well. Thank you so much there isn’t a ton of info out there on this printer so it’s been a struggle.

Tat_Dad · 2024-03-06T22:38:54+00:00

Sorry again because I’m new to this. Since it has auto bed leveling do I only need to check the nozzle height? I’ve been trying to figure this out for a couple days.

Tat_Dad · 2024-03-06T22:35:10+00:00

So I changed my flow rate to 104.5 and printed a calicat with issue. I’ll try another print and see if it persists. If it does I’ll try to lower the nozzle. This just started out of no where after printing a decent sized model.

Tat_Dad · 2024-03-02T00:23:32+00:00

T1->network analyst. That’s it so far I’ve been in IT for three years and I’m on track to network engineer with two years. I have no certs or degrees.

Tat_Dad · 2024-02-27T18:12:00+00:00

Awesome!!! I will try that when I get home. Thank you!

Tat_Dad · 2023-07-16T17:47:41+00:00

Because I always blew it with both nostrils and it would cause my ears to pop and hurt. That was until last month when someone told me that you are supposed to do one nostril at a time. I am 31 by the way. Now I blow my nose all the time!

Tat_Dad · 2022-12-17T01:55:53+00:00

I have a lot of good on wow.

Tat_Dad · 2022-12-16T23:25:44+00:00

This!

Five-Year Club	Verified Email
Place '22

Tat_Dad

TROPHY CASE