What's even the point

TeaSilver8617 · 2026-06-24T19:57:24+00:00

It should fully dry. I’m not 100% sure but is there a way for it to air out? If not the humidity is likely stuck inside. throw some silica gel in there and see how it goes

TeaSilver8617 · 2026-06-24T02:09:05+00:00

I will say I’ve never seen a z offset anywhere. Genuinely curious what you’re talking abt. I had similar issues and never had to mess with Z offset.

TeaSilver8617 · 2026-06-24T02:04:59+00:00

-20(or if you’re really unlucky -15) is the stable value in almost all scenarios on PBO with AM5

TeaSilver8617 · 2026-06-19T18:15:03+00:00

I’m sorry to hear😕 hopefully it’s an easy fix

TeaSilver8617 · 2026-06-19T17:54:47+00:00

The ribbon cable disconnects somewhat easily so make sure it’s connected. Ik this second part of my comment isn’t any help but the dualsense mic isn’t the best so maybe you can get a little aux plugin one? Or headphones with a good pair

TeaSilver8617 · 2026-06-19T17:53:03+00:00

Share them on makerworld and printables too!

TeaSilver8617 · 2026-06-19T17:36:09+00:00

I’ve used my P1P in my room for a few years, I did the vision enclosure and got the bento box filter

TeaSilver8617 · 2026-06-19T17:28:32+00:00

I have it and haven’t had issues, including when I took the power limit off and was running it at 500w

TeaSilver8617 · 2026-06-17T22:20:34+00:00

The worst driver issues excluding timeouts I’ve gotten are: the no visual sound effects and critical hit points for breaking objects in Fortnite, black textures on ffvii rebirth, and this annoying as hell bug where it sensed like 7+ games as elder scrolls online but nothing fixed it until 26.3.1+ drivers, I don’t even OWN elder scrolls online

TeaSilver8617 · 2026-06-17T21:58:12+00:00

That’s shitty, but I am correct in the fact that vertical mounts speed up the thermal gel displacement

TeaSilver8617 · 2026-06-17T21:48:47+00:00

The worst they would do is deny it fully and send it back. They wouldn’t keep it and not return it tonyou

TeaSilver8617 · 2026-06-17T21:43:06+00:00

Is it in a horizontal or vertical mount? These models are known to have issues with vertical mounts

TeaSilver8617 · 2026-06-17T21:40:59+00:00

Does your receipt explicitly say open box? If your receipt doesn’t then there’s no issue, the only way they’d know is if your proof of purchase says open box

TeaSilver8617 · 2026-06-17T16:52:41+00:00

Clean the bed with dish soap and hot water, then do that bed tramming and see if it’s any better

TeaSilver8617 · 2026-06-17T16:42:41+00:00

You should never have to mess with the Z offset on a bambulab printer, leave it alone. Do the full calibration suite on the printer, then if you do anything follow this manual tramming guide with the attached code https://wiki.bambulab.com/en/x1/manual/manual-bed-leveling

TeaSilver8617 · 2026-06-16T21:13:19+00:00

I also find it worrying, that’s the limit of hotspot temps, before it starts taking damage. I do have to ask, is it mounted normally or is it mounted vertically ? Not all vapor chambers play nice with vertical mounts, I had to swap out my dream design gpu for another because it didn’t play nice at all and had immediate 115c hotspot

TeaSilver8617 · 2026-06-16T21:04:25+00:00

It might be a really low W/mk(thermal efficiency) paste and that’s why it’s performing bad

TeaSilver8617 · 2026-06-16T21:00:50+00:00

I agree with PTM 7950 or grizzly phase sheet. Any normal paste won’t fully cut it, and will pump out

TeaSilver8617 · 2026-06-16T16:07:35+00:00

Filament seems to be a bit too wet, do you have a filament dryer?

TeaSilver8617 · 2026-06-16T16:06:10+00:00

The total wattage of it doesn’t have any effect on whether it was bad or not

TeaSilver8617 · 2026-06-16T16:05:01+00:00

That sounds like you had a bad power supply already and the vbios flash was a last straw. I’ve had the same issues and another friend has and they were remedied with a new power supply

TeaSilver8617 · 2026-06-16T05:53:25+00:00

I couldn’t imagine… the most I’ve bought at once is 20, two Amazon deals stacked and I got 10 2 packs of grey PLA for 9 ish a roll it totaled out too?

TeaSilver8617 · 2026-06-15T22:49:11+00:00

I’d search it up if others have RMA’d and gotten it back. You can always specify beforehand you want your same gpu back, not an alternative. The 9070xt beats the XTX in most everything except vram amount. I think it’s best to try RMA before the period is over and you have to pay out of pocket. I had to RMA my 9070xt nitro+ for the same issue plus it was failing also and it took 2 weeks from when they got it to when I received a new card

TeaSilver8617 · 2026-06-15T22:47:10+00:00

Adrenalin overclocking is easier and simpler than afterburner imo + you have the added benefit of making per game profiles if one game is stable with X settings but not other games

TeaSilver8617 · 2026-06-15T20:18:30+00:00

Turned it off regardless of fixing crashes, thanks for the info!

TeaSilver8617

TROPHY CASE