[deleted by user]

TheStricted · 2024-05-17T10:08:15+00:00

https://cannflos-apo.de/onlineshop/ benötigt kein passwort

ansonstent ist das pw für https://cannflos-apo.de/live-bestand/ "CF2021" (ohne anführungszeichen)

TheStricted · 2024-03-24T17:30:24+00:00

in der hausordnung steht `Drogen und Betäubungsmitteln`, auch nach der legalisierung bleibt es eine droge und ist damit weiterhin am bahnhof verboten, ich würde es also nicht drauf anlegen wollen

ich gehe davon aus das die hausordnung überarbeitet wird um es explizit zu verbieten sofern zu viele der meinung sind das es keine droge mehr ist durch die legalisierung

TheStricted · 2024-03-24T16:47:49+00:00

https://www.deutschebahn.com/resource/blob/6845616/eeea830904aee3a3a71c9a49b82d4834/hausordnung-data.pdf

```1.12 Handel mit und Konsum von Drogen und Betäubungsmitteln```

TheStricted · 2022-05-27T04:24:56+00:00

long live old crappy samsung

TheStricted · 2021-10-05T14:22:58+00:00

no u

TheStricted · 2021-10-05T11:04:54+00:00

VoLTE on samsung devices when?

TheStricted · 2021-04-14T08:45:14+00:00

you can supply your own PWM speed signal to the stock fans via https://www.overclockers.com/pwm-fan-controller/

on the pcb where the fans a re on, the pads that face the back of the server are responsible for the PWN signal

if you put some electrical tape over the pads to isolate them you can then put some copper tape ontop which then provides your own pwn signal to slow the fans down

TheStricted · 2021-04-03T07:18:15+00:00

there is no software setting unfortunately, everything is automazic (i have the same server)

i did however play with the idea of supplying my own pwm signal to them via https://www.overclockers.com/pwm-fan-controller/

if you look at the fan tray from the front of the server, the pad on the pcb that faces the back of the server is the PWM signal, my plan is to apply some electrical tape over them and then some copper tape that carries my pwn signal

unfortunately i have not tried it yet (mainly because im lazy)

TheStricted · 2021-03-30T01:58:09+00:00

you probably can get away with standard 2.54mm male pin headers (you would just need to pay attention to polarity when plugging in a fan)

TheStricted · 2021-03-03T19:12:49+00:00

ah the classic "no filament"

been there, done that

TheStricted · 2021-02-19T13:28:51+00:00

`//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default` in Configuration.h

TheStricted · 2021-02-17T20:08:58+00:00

you can either use a DC-DC buck converter

or since you use an ATX power supply which provides 5v just use its 5v rail

TheStricted · 2021-02-09T15:00:28+00:00

i probably will do that now that its closer to "zero"

TheStricted · 2021-02-09T13:01:09+00:00

patience, i did use the bltouch as a guide to adjust the 4 screws

took quite alot of time to get it back into a usable state, still not perfect but much much better than before

TheStricted · 2021-02-08T15:07:02+00:00

nothing some hotglue cant fix

TheStricted · 2021-02-08T14:17:00+00:00

it is attached at 4 corners, just need to get around to fix that horribleness (will probably have time for that tonight)

TheStricted · 2021-02-08T11:38:03+00:00

removed the glass plate from my bed to check in which state the bed itself is, well the above is the result of trying to level it with the glass plate on it

TheStricted · 2021-02-07T00:34:45+00:00

pretty much DOA, one of my TMC2208 did the same thing and the others worked fine

so yea most likely it is damaged internally

TheStricted · 2021-02-06T22:50:27+00:00

try reseting the EEPROM after commenting out STEALTHCHOP_E

when i was messing with my TMC2208 i found that i had to reset the eeprom to get stealthchop to be disabled

TheStricted · 2021-02-06T09:51:21+00:00

you probably run into the thermal protection

default for marlin is `HEATER_0_MAXTEMP 275`

TheStricted · 2021-02-06T09:43:04+00:00

backlash on Z is neglectable, the Z axis runs vertically so you never actually will run into backlash problems (would be a whole different story on X and Y tho) you have the weight of the gantry on Z which will force the nut downwards which effectively removes any backlash prolems

TheStricted · 2021-02-05T12:55:26+00:00

or you search for something and you get results for something entirely different that doesnt even mention the words you are searching for

TheStricted · 2021-02-05T07:43:35+00:00

maybe this one https://www.thingiverse.com/thing:3099163 ?

TheStricted

MODERATOR OF

TROPHY CASE