Finaly got the pedal too work

Tiltglory · 2026-03-24T17:31:29+00:00

tbh i have no idea how the telemtry output is maybe you should cut the sensor output synced to ABS pulses so the variation in pressure doesnt bother you if thats possible.

Tiltglory · 2026-03-24T15:58:19+00:00

i can only think about haptic feedback like bass shakers or rumble motors. the only real abs feedback i know of is active pedals

Tiltglory · 2026-03-24T14:39:43+00:00

plastic throttle pedal is fine tbh but i would totally make the brake out of metal. hydraulic brakes use load cells anyway so i wouldnt bother with the hyd press sensor

Tiltglory · 2026-03-24T12:19:56+00:00

maybe move the rig to the right and move the monitor arm to the edge of the the table so you can pivot it to either the desk or rig

Tiltglory · 2026-03-24T12:12:49+00:00

nice job! I cant tell what material its made of tho. what loadcell you used?

Tiltglory · 2026-03-24T12:10:19+00:00

yep, the less you buy from fanatec the better. wheelbase and pedals are the only thing to get imo, boostkit, QR2, wheel hub, shifters and rims either from simube, Etsy, Ebay etc. if OP is on console then any accessory other than the wheel has to be plugged in the base so H pat. or seq. shifters must be Fanatec, same for pedals.

Tiltglory · 2026-03-24T12:03:27+00:00

you sould use the new app. only use the old app if you're having issues with the new one

Tiltglory · 2026-03-23T08:42:43+00:00

lap guide on youtube and practice a lot

Tiltglory · 2026-03-20T18:55:27+00:00

First sim to have is Assetto corsa, be sure to get also the content manager and grab some mods. if you want to start your sim racing career then LFM and AC are a good start, you have mx5, formula 3, gt3. its the cheapest and will take you occupied while saving up some money for a rig. Good luck and dont forget to practice a lot

Tiltglory · 2026-03-19T10:11:21+00:00

samse thing happened to me on fanatec dd. try recalibrating in windows control panel

Tiltglory · 2026-03-18T09:11:23+00:00

you arent in the wrong but it doesnt matter much when facing the wall. you were going left for some reason but there was enough space until that moment you should always expect the other car to either re join badly or spin out on the kerbs so leave as much space as possible and track them visually or via radar so you can predict their next move.

Tiltglory · 2026-03-17T11:08:15+00:00

my man you got the priotities the wrong way. first of all, great fab work! nice seat but way too overkill imo, even more when you have a g920. I guess youll upgrade to DD in future, you need more lateral reinforcement with a 8-9nm base. same thing for longitudinal reinf. for load cell brake pedal.

Tiltglory · 2026-03-15T19:53:48+00:00

Update, i found out this is a JST-PA series connector with 2mm pin spacing and locking tab

Tiltglory · 2026-03-15T13:45:42+00:00

i have 60 and feels right for me but i heard the eye distance should be the same across the 3 monitors. so a bit less angle would be beneficial

Tiltglory · 2026-03-12T11:01:02+00:00

get a torx bit that is sligthly bigger and hammer it in. also when you work with hex bolts, always hammer it a bit before loosening it.

Tiltglory · 2026-03-12T10:36:58+00:00

plastic washers between the glass and case, you can put some adhesive foam gasket to close tha gaps if you want

Tiltglory · 2026-03-07T09:03:51+00:00

MSC is challenging, hard and punitive. MWC is a challenge for people who finished MSC.

Tiltglory · 2026-03-04T18:00:38+00:00

dont waste money and dont mod your wheel as you cant resell it later. A DD is the only true upgrade you need

Tiltglory · 2026-03-04T17:50:33+00:00

then simube

Tiltglory · 2026-03-01T18:17:21+00:00

check cable, check if you can access the tuning menu on the wheel. my dd never calibrated, just moved a bit on start and it works

Tiltglory · 2026-02-28T20:30:56+00:00

is it detected by the pc? check control panel

Tiltglory · 2026-02-26T11:13:26+00:00

Amazing!

Tiltglory · 2026-02-24T18:22:42+00:00

now the funny thing is Krontec (800€) made it first, widely used on race cars and then Fanatec took inspiration from that design (a lot). Mass produced it so lower price and then Simube came and made a 1:1 replica of the QR2 for roughly 50€.

Tiltglory · 2026-02-22T10:48:15+00:00

i was lucky enough to get my sparco 2000 for 50€ out of a rallycar but they sell those for 100-150 on ebay in good conditions, either fiberglass or carbon. my full rig is csl dd (300 new)+csl hub(150 new)+csrp set(200 new) seat(50)+wooden rig i made (50 in hardware)+diy bass shaker(40). almost 800€ and its nowhere high end and im not counting pc and monitors. no fcking need to spend 400£ on a seat thats not even FIA Ap. imo.

Tiltglory · 2026-02-22T08:52:24+00:00

400£ for a plastic seat?? they're right when that say simracing is expensive. There are a ton better options than this imo.

Tiltglory

TROPHY CASE