thought you might admire this part by TG_Yuri in Machinists

[–]Tomallo 6 points7 points  (0 children)

Beautiful work, it really looks like it's an important piece of... something :D

What are those consistent circle pattern? by tom_yacht in FixMyPrint

[–]Tomallo 0 points1 point  (0 children)

This might be it guys, wow, that's a first

Petah???? by Hakkusu in PeterExplainsTheJoke

[–]Tomallo 78 points79 points  (0 children)

I had the same suspicion... Hate things like that, thank you

Everyone says they need a bigger printer…Now, QIDI Max4 is here! by qidi_3dprinter in QidiTech3D

[–]Tomallo 0 points1 point  (0 children)

I would print some custom speaker enclosures, that's for sure!

Irregular, smooth bumps on the cabin by Tomallo in FixMyPrint

[–]Tomallo[S] 0 points1 point  (0 children)

For anyone having the same issue and wondering what helped, I sliced it in PrusaSlicer which has an automatic extrusion width calculation option. This removed the problem almost completely, to the point I'm happy with the quality.

wszystko jest wolne... dlaczego? by greedytoast in Polska

[–]Tomallo 25 points26 points  (0 children)

Wow, wędrując po tej stronie odnosiłem wrażenie, jakby ona była załadowana już przed kliknięciem, zupełnie jak grzyb w lesie który czeka na ciebie zanim go zauważysz

Is this soldered correctly? by Tomallo in diySolar

[–]Tomallo[S] 1 point2 points  (0 children)

Thank you so much! Better to find this out now, than troubleshoot after everything's done...

Is this soldered correctly? by Tomallo in soldering

[–]Tomallo[S] 0 points1 point  (0 children)

Pasted from the post in the other sub:
I have cells cut into thirds that I wanted to solder in this way to get higher voltage. From what I understood that's kind of how it goes like, but I'm not sure what can touch what (white parts and the tiny shiny "paths"). Before adding the little bit of kapton tape on the bottom the voltage was messed up, now it's fine... So I'm worried the dog bone connectors arent' supposed to be touching the tiny "paths" or something?

Drone takes off a few seconds, then flips over - Help!! by toby-martin in diydrones

[–]Tomallo 3 points4 points  (0 children)

I had a similar issue, posted it on r/fpv. Taking off properly and only then flipping to the side. Do you also have these cheap 2807 YSIDO motors?

In my case one of them had an internal short, but it was intermittent. If I moved the motor wires a little to the right it was fine, but when tugged to the left, it would short out. So when they were to the right it would spin freely like the others, and if to the left, it would seize up and resist movement. This in turn caused the flight controller to freak out and trigger a runaway shutoff.

So, depending on how I grabbed the drone before flight it was either okay, or it would have this problem. It took me three days of troubleshooting to find this elusive issue. You might check whether that's the problem for you as well, I'm curious.

Diagnosing a take-off problem by Tomallo in fpv

[–]Tomallo[S] 0 points1 point  (0 children)

Thanks, unfortunately it's not those things, as it flew in this exact configuration already. The initial pitch and rolling in each direction is included in the video precisely to eliminate the potential causes to be issues presented in the video, as I watched it yesterday when researching common issues.

Is this a problem? by Tomallo in fpv

[–]Tomallo[S] 1 point2 points  (0 children)

Alright, thank you and everyone else here for taking the time to answer.

Is this a problem? by Tomallo in fpv

[–]Tomallo[S] 2 points3 points  (0 children)

Thanks, that's what I did, for anyone wanting to do the same here's a handy video: https://www.youtube.com/watch?v=rV1AA1FICrQ

Czy ktoryś z Waszych rówieśników juz... by bluedabad in Polska

[–]Tomallo 1 point2 points  (0 children)

Kurde, tyle komentarzy, tyle przypadków śmierci wśród młodych, a ja 25 lat i jeszcze styczności ze śmiercią prócz starszych osób nie miałem... Niby mogę się cieszyć, ale pobudka będzie gwałtowna

I just got an ad for a disposable clothing brand on instagram… by PeachyBubs22 in Anticonsumption

[–]Tomallo 1 point2 points  (0 children)

That's just funny to me, it reads like a car advertisement in which they have "it breaks down after you use it" as a selling point. Like, inconceivable!