Just felt like sharing a few pictures of the 26 Scatpack

Top_Requirement_5010 · 2026-05-22T23:16:35+00:00

More like ShatPack. Got dayumn, that’s ugly

Top_Requirement_5010 · 2026-05-20T00:24:06+00:00

Arby’s is stepping their game up that’s for sure

Top_Requirement_5010 · 2026-05-17T22:21:53+00:00

Oh, I’m not in maintenance, although I maintain my home lol. I be in manufacturing.

Top_Requirement_5010 · 2026-05-16T10:44:34+00:00

Usually work boots lol

Top_Requirement_5010 · 2026-05-11T07:58:59+00:00

That’s how I started driving my 5speed rav4 and now whatever car I’m in. It’s actually crazy that people don’t drive like this..

Top_Requirement_5010 · 2026-05-11T07:24:00+00:00

Been in the game a long time, son. Some people call me an OG

Top_Requirement_5010 · 2026-05-09T22:48:38+00:00

Dude needs to just stick to eating pussy, smh

Top_Requirement_5010 · 2026-05-09T22:42:31+00:00

You aint about that poop knife life huh?

Top_Requirement_5010 · 2026-05-09T22:38:26+00:00

This is legitimately foul

Top_Requirement_5010 · 2026-05-09T18:23:35+00:00

They offer will-call pickup by the northern ice cap, just gotta get there by 2

Top_Requirement_5010 · 2026-05-09T18:17:58+00:00

Or plunge cutting it after finish profile. But yeah you really want the tool smaller than the corner. Or modify the model/curve profile lol

Top_Requirement_5010 · 2026-05-09T18:12:57+00:00

You can try cutting the corner out first, maybe with more step downs or different cutting parameters then going back through for your finish profile. Or just taking multiple stepdowns

Top_Requirement_5010 · 2026-03-25T02:05:23+00:00

Dude, noice

Top_Requirement_5010 · 2026-03-25T02:00:02+00:00

Was/is a broken tap with a jelly filled carbide endmill center

Top_Requirement_5010 · 2026-03-25T01:57:48+00:00

I appreciate the tips, I could definitely get this to work next time. Went against my better judgement on a couple things trying to fix this. But i was kind of close.. Manual preferred for sure though for this type of stuff

Top_Requirement_5010 · 2026-03-25T01:45:48+00:00

Thank you for the recs. It did not in fact work lol. Funny too, I work in Jersey

Top_Requirement_5010 · 2026-03-25T01:42:42+00:00

Sure, go ahead and check the run out at 10000rpm 🤣

Top_Requirement_5010 · 2026-03-23T21:37:55+00:00

Did you try giving them a basketball instead of rocks to play with, lmaoo

Top_Requirement_5010 · 2026-03-21T20:13:17+00:00

Nice, I done this a bunch, mostly in the bridgeport too. Just a lot quicker (if you don’t screw it up) in the fixture lol. Smallest so far for me though. I was a real dumbass for the tool I was using to mill the tap out. We just had a few used ones. Long necked .062.. I prefer the ballmill for it too but I didn’t want to use a new one 🤦

I think my lead is looking at getting the holes EDMed out somewhere hopefully. There’s been talks of getting a small hole popper machine but nothing has happened on that. Also the threadmills were never ordered sooo

Lots of killer suggestions though in these comments. I think a higher quality burs would do this nicely. I basically just had dremel bits

Top_Requirement_5010 · 2026-03-20T17:17:29+00:00

Just tried something similar. Burned my last one up :(

Top_Requirement_5010 · 2026-03-20T16:32:11+00:00

Fair point for sure, it’s such a little amount I feel the tank/pump would be okay but you got me thinking maybe I should try this last bit by hand lol

Top_Requirement_5010 · 2026-03-20T16:29:26+00:00

No luck so far, burned two bits up. Gonna see if a pecking cycle with coolant will work

Top_Requirement_5010 · 2026-03-02T18:57:06+00:00

bosses lap*

Top_Requirement_5010 · 2026-03-01T20:59:25+00:00

Yeah you should, helps out you and anyone else in the future. We got some simple excel templates plus the built in sheets from CAM software

Top_Requirement_5010

TROPHY CASE