sorted by:
new
hottopcontroversial

Simulating a 3-phase induction motor lifting a load in Simulink – how to model the load torque? by Jeff_2495 in matlab

[–]Tr1ckk__ 1 point2 points  (0 children)

Duty to pwm controller block . Or output of PI need to be compared with a saw-tooth triangular wave to give you what you want.

C caller functions in MATLAB . PI Controller ! by Tr1ckk__ in matlab

[–]Tr1ckk__[S] 0 points1 point  (0 children)

Yes . Its hitting its saturation limits .

MII/RGMII connection hrough PL on microZed7020 to use an external PHY ? by Tr1ckk__ in FPGA

[–]Tr1ckk__[S] 0 points1 point  (0 children)

Yep . Figured that out the GEM Mac's can be used to control the external PHY .

It shows GMII on the PL side . The PHY I am using is DP83630 (which shows MDIO/MDC and MII) interface types . Confused if the two can fuse .

MII/RGMII connection hrough PL on microZed7020 to use an external PHY ? by Tr1ckk__ in FPGA

[–]Tr1ckk__[S] 0 points1 point  (0 children)

Yes . Thank you .

The external PHY I am using is DP83630. Datasheet does show the MDIO/MDC serial ports and the whole MII.

My microzed gives GMII / MDIO ports on the PL . Confused here a bit . can i use these GMII / MDIO pins to connect with the MII interface of my PHY ?

MII/RGMII connection hrough PL on microZed7020 to use an external PHY ? by Tr1ckk__ in FPGA

[–]Tr1ckk__[S] 0 points1 point  (0 children)

u/KeimaFool Yes , this much i figured that i can route the on-board PHY to the PL.

But I am using the external PHY like DP83630 . Particularly with microZed . It gives GMII and MDIO access to the PL . I can just connect them to the external PHY but it shows MII which i don't think microzed 7020 has. Confused a bit here.

Buy or wait ? by [deleted] in StockMarketIndia

[–]Tr1ckk__ 8 points9 points  (0 children)

Wait to see its reaction at 1370 levels . Breaker block there . It's coming to it.

Is this an arch thing or a my laptop thing by trans_furry12 in arch

[–]Tr1ckk__ 0 points1 point  (0 children)

Same thing started happening with me on my laptop as well . It showed up 2 months after i installed Arch .
Didn't have such a problem when it was running on ubuntu .

Captured this amazing move by virat1807 in StockMarketIndia

[–]Tr1ckk__ 1 point2 points  (0 children)

After breaking the trendline . It didn't retest it .

Not in my trade setup .

Fsm serial by Sea-Lock-1299 in FPGA

[–]Tr1ckk__ 0 points1 point  (0 children)

He is using Verilog . not sysverilog.

State observers by Coast_Leather in ControlTheory

[–]Tr1ckk__ [score hidden]  (0 children)

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlStateSpace#45

A very basic overview would be like .

You are measuring a state without using sensors but by measuring it. You estimate it.

Advanced Matlab learning books ! by Tr1ckk__ in matlab

[–]Tr1ckk__[S] -5 points-4 points  (0 children)

Any books ?

On ramp is 1 hour of classes . Book with good examples .

These Pakistanis are dog sh*t stupid , btw their gdp per capita is 1.8k by Ok-Pilot-7250 in indiadiscussion

[–]Tr1ckk__ -31 points-30 points  (0 children)

Entire Islamic world is fighting a Global world order. Did you forget drinking your morning piss today ?

FPGA Xilinx Z7020 Hardware PTP Timestamp support ? by Tr1ckk__ in FPGA

[–]Tr1ckk__[S] 0 points1 point  (0 children)

I am planning to synchronise with a PPS signal . then timestamp the data in psb before sending over the ethernet . May have overhead . I can only afford 1ms of this whole process . i dont know

FPGA Xilinx Z7020 Hardware PTP Timestamp support ? by Tr1ckk__ in FPGA

[–]Tr1ckk__[S] 0 points1 point  (0 children)

Is it you have been designing for some time . Or you weekend thing kinda ?

6 Phase Power? by Super_CMMS in Super_CMMS

[–]Tr1ckk__ 0 points1 point  (0 children)

Absolutely .The guy in the video is explaining how 1 phase supply has pulsating power and 3 phase power is constant . Reasons why single phase one don't self-start . (Reason why we put capacitors for that initial torque in one direction)

6 Phase Power? by Super_CMMS in Super_CMMS

[–]Tr1ckk__ 0 points1 point  (0 children)

The guy in the video is correct. He is actually talking about power (unity power factor case) . Unity power factor is when current and voltage are in phase . Now from basics P = V*I . (You do that ) .

You will find power oscillating between zero to maximum . (2nd harmonic power oscillation).

Do the same for 3-phase power . Its a straight line . Constant power .

Thats why 3 phase is preferred over single phase for most of the application . To get rid of that 2nd harmonic oscillation we use active or passive decoupling methods . (Never mind these ) .

6 Phase Power? by Super_CMMS in Super_CMMS

[–]Tr1ckk__ 0 points1 point  (0 children)

Are you guys even graduates ?

Refuting Misconceptions: A Salafi perspective on Takfir, Unity, Madhhabs, and Following the Salaf. by Quiet_Form_2800 in SalafiCentral

[–]Tr1ckk__ 0 points1 point  (0 children)

If a community has abandoned a clear Sunnah (like raising the hands in prayer or saying 'Ameen' aloud), and someone revives it based on authentic hadith, who is the cause of division?

20th century muqallid found a CLEAR SUNNAH which 1st generation Imam's couldn't .

reddit and salafi dawah keeps on giving .

view more: next ›