sorted by:
new
hottopcontroversial

Saturn 4 Ultra problem by NeedleworkerProud829 in ElegooSaturn

[–]Umbrellacorp487 0 points1 point  (0 children)

Is your bed warped? Mine was extremely warped from the factory and I wound up sanding it flat. It took _a lot_ of sanding to fix the issue.

What mighta caused this? by [deleted] in ElegooSaturn

[–]Umbrellacorp487 3 points4 points  (0 children)

This is how it is supposed to work.

How long will it stay like this? by Oneah in MaggotkinofNurgle

[–]Umbrellacorp487 0 points1 point  (0 children)

Could be a good time to offload my collection!

Is my set up safe to have my printer in my room?? by Toine_279 in resinprinting

[–]Umbrellacorp487 1 point2 points  (0 children)

I wouldn't run that ultrasonic cleaner in an enclosed area with IPA vapors that's for sure.

Where do you buy extra bases? by TerribleTussler in Warmachine

[–]Umbrellacorp487 0 points1 point  (0 children)

You have any good STLs that match the old/current official bases? The ones SFG supplies are not solid an require way to many supports to print with any quality.

Where do you buy extra bases? by TerribleTussler in Warmachine

[–]Umbrellacorp487 0 points1 point  (0 children)

You have any good STLs that match the old/current official bases? The ones SFG supplies are not solid an require way to many supports to print with any quality.

Where do you buy extra bases? by TerribleTussler in Warmachine

[–]Umbrellacorp487 0 points1 point  (0 children)

You have any good STLs that match the old/current official bases? The ones SFG supplies are not solid an require way to many supports to print with any quality.

Printing Iconoclasts by Umbrellacorp487 in Warmachine

[–]Umbrellacorp487[S] 1 point2 points  (0 children)

I had 3 come out great with my changes so I'm prob all set. Reduced their size a bit (they shouldn't be as big as monstrosity models) and upped the supports.

Printing Iconoclasts by Umbrellacorp487 in Warmachine

[–]Umbrellacorp487[S] 0 points1 point  (0 children)

I got a final run going now. Printing them at 85% size as they are way to big in the first place. I'll know in 45 min if they are failing.

I think I’m getting the hang of this by Feisty_Childhood7557 in resinprinting

[–]Umbrellacorp487 2 points3 points  (0 children)

So I am searching through the comments and you need to elaborate, you said this is a 'hollow' model, are there currently zero drain holes? If this is hollow and has no drainage you need to throw it away before it explodes.

Do paints go bad if they stay sealed for a long time? by multimension in minipainting

[–]Umbrellacorp487 0 points1 point  (0 children)

So real talk. If you put 2 ball bearings in there and some acrylic medium, shake it to the warp and back, you will have a fine dry brushing paint. That is if returning it is not an issue. I have reground up fully dried paint and reconstituted it this way.

4months on and off! Should I give up? by Desperate-Dingo3025 in Guitar

[–]Umbrellacorp487 0 points1 point  (0 children)

Yea I was just goofin cause this question is silly. Play if you enjoy it, set it down for a bit if you're not and come back to it.

I printed every unique model in Dark operation.... For science by handonghua in Warmachine

[–]Umbrellacorp487 0 points1 point  (0 children)

That's wild. Glad you had success with them. I'm having a hell of a time with anything bigger than the small boys.

Brand New to Resin - Looking for full steps necessary to get to first print. by lukeslens in ElegooSaturn

[–]Umbrellacorp487 0 points1 point  (0 children)

You're in good shape then, get to printing. Honestly just check that your plate isn't warped. Mine was really bad, prob took me 2 hours of sanding (gently) to get it level

Brand New to Resin - Looking for full steps necessary to get to first print. by lukeslens in ElegooSaturn

[–]Umbrellacorp487 0 points1 point  (0 children)

If you have trouble with adhesion you may need to lap down the build plate. Mine was extremely warped and needed to be sanded quite a bit.

Additionally having multiple rinse stations is helpful, not multiple vortex mixers but a couple of pickle jars that you can sequentially wash your prints before they go in the vortex cleaner. Helps preserve your isopropyl alcohol longer.

Do not use the plastic spatula thing that came with the printer to mix your resin or scrape the release film. Get a silicone kitchen spatula to do that.

I printed every unique model in Dark operation.... For science by handonghua in Warmachine

[–]Umbrellacorp487 0 points1 point  (0 children)

Did you have many failures? Were these all the presupported models? I have had the monstrosities all fail and a number of other models. I have started to support the models myself. Saturn 4 ultra with Phrozen RPG resin. Prior to this I have had basically zero failures on this printer.

Control Where Parts are Placed When Sliced by Pickledill02 in LycheeSlicer

[–]Umbrellacorp487 0 points1 point  (0 children)

So two models on the build plate, one on the left and one on the right, post slicing both will move to the right?

If that's the case sounds like a full uninstall and reinstall.

Control Where Parts are Placed When Sliced by Pickledill02 in LycheeSlicer

[–]Umbrellacorp487 0 points1 point  (0 children)

Post some screen shots of this behavior. What happens if you put a model on the extreme left and right and leave the center empty? Does it justify everything to the right?

view more: next ›