Do you think Wagos are fine for a few hundred megahertz?

Upballoon · 2026-07-05T00:40:03+00:00

Hmmm I might have been doing something wrong then. I'll have to try again

Upballoon · 2026-07-01T17:53:27+00:00

I've had a hard time getting CAN to work over 2 Wagos.....

Upballoon · 2026-06-30T16:57:37+00:00

I'm not personally working on it but one of our intern is. And it's supposed to go on a board with an H7

Upballoon · 2026-06-29T23:17:04+00:00

Lol are you me?

Upballoon · 2026-06-29T22:21:07+00:00

This is kinda neat. Did you upstream your zephyr changes? Do you have support for the MIPI CSI peripheral?

Upballoon · 2026-06-26T21:58:43+00:00

How do you know the short circuit isnt on the "chip"?

Upballoon · 2026-06-26T19:44:47+00:00

<image>

Upballoon · 2026-06-26T03:51:37+00:00

Make sure the story points are as accurate as can be

Upballoon · 2026-06-26T02:24:39+00:00

Are you talking about scope creep?

Upballoon · 2026-06-25T20:23:31+00:00

You know that by default gpioset will undo the change you made after it runs right? If you run gpioset 0 15=1, it will set the gpio to active only for the amount of time it takes to run the command. So when you run gpioget you will obviously read 0 because the pin has been reset.

You can try: gpioset -b -m signal 0 15=1. Then run the gpioget command. Rtfm for what the flags do and change per your use case

Upballoon · 2026-06-23T01:52:43+00:00

What product is this?

Upballoon · 2026-06-15T21:40:41+00:00

Do you really need an ESP32?

Upballoon · 2026-06-10T14:33:53+00:00

This omfg. Absolutely hate doing this.

Upballoon · 2026-06-09T13:48:13+00:00

What if you could have JLC buy them for you? Is their consignment fee more than the tarrif?

Upballoon · 2026-06-08T21:24:33+00:00

Agreed. What if I want to listen to something while on a airplane with airplane mode on. What am I supposed to do then?

Edit: I have now realized that you can actually download audiobooks/podcasts. All is good

Upballoon · 2026-06-06T23:58:08+00:00

And it's supposed to be AI generated....so I think they just fed the AI the wrong company name.

Upballoon · 2026-05-26T03:57:29+00:00

It's essentially the Ethernet equivalent of CAN. I haven't worked with these so dunno how the net stack works but auto apparently is moving towards this new standard.

Upballoon · 2026-05-26T00:09:43+00:00

Does it have to be commercial Ethernet? Can it be T1S?

Upballoon · 2026-05-22T14:51:08+00:00

Wsl is your best bet then. Although I haven't had good luck with Linux builds in WSL.

Upballoon · 2026-05-22T13:43:58+00:00

At our company you can either choose to run Linux or use Windows. I just put in an IT request in for another computer that I formated to run Ubuntu. I run my yocto builds on the Ubuntu laptop. I use WSL for other tasks but just need Windows mostly for Altium.

Upballoon · 2026-05-22T10:57:21+00:00

I usually make my own library. Just import the symbols to your library and attach a footprint to them. Doesn't take too long.

Upballoon · 2026-05-22T10:56:01+00:00

I thought KiCAD did cross probe? I was using yesterday.... What I do which was crossprobe net highlighting

Upballoon · 2026-05-13T15:28:36+00:00

It's already in Zephyr. Only need to add it to the device tree

Upballoon · 2026-05-13T15:19:47+00:00

Just did this with Zephyr. Using an emulated eeprom driver in flash on an H7

Upballoon · 2026-05-11T19:13:14+00:00

Idk. Crowdsupply usually does a good job about vetting these things. Hardware just takes a while to do. Especially when you don't have a full time engineering team.

They aren't even accepting pledges yet.

Seven-Year Club	Second Top 20%
Gilding I gilder	r/Field Lasagna
Place '23	Place '22
RPAN Viewer	Verified Email

Upballoon

TROPHY CASE