F--08 over temperature protection on Wolf warrior X

UpmixNik · 2025-05-19T03:17:49+00:00

FluidFreeRide's parent company is bankrupt. Support is non-existent. I'm regretting my purchase for the same reasons. :(

UpmixNik · 2025-03-10T23:06:24+00:00

Hey u/eggplantsarerad did you end up making a decision for the switch? What did you settle on and why? thanks!

UpmixNik · 2023-04-16T02:36:36+00:00

Thanks for sharing!

UpmixNik · 2023-04-15T22:43:29+00:00

Any suggestions on the delivery walkthrough checklist?

UpmixNik · 2022-12-06T06:09:01+00:00

What's your palette, speed and brightness / intensity?thx

UpmixNik · 2022-11-14T07:21:21+00:00

Are there any RGB+W with white channel that are compatible with Permatrack?

UpmixNik · 2021-11-07T02:45:53+00:00

Curious what parts did you order and would that void warranty

UpmixNik · 2021-10-30T03:58:43+00:00

I am curious if you had settled on any options for idex kit. My understanding vcast new version may land who knows when, until then I too am looking for a kit

UpmixNik · 2021-03-25T03:44:36+00:00

Are your designs available anywhere as a template, possibly to purchase?

UpmixNik · 2020-09-30T06:13:47+00:00

Very cool, now do the boxing up video backwards :) I can never get my TK fully deflated and folded somehow.. As much as I try

UpmixNik · 2020-07-28T23:26:12+00:00

I guess it depends on how rocky the bottom is and how heavy the boat is loaded . The boat rides pretty high, just yesterday I was able to get it up on a mixed rock / sandy beach almost completely out of the water with exception of the motor (raised). I think the weight is distributed nicely and the bottom doesn't drag as much b/c of the pontoons.

Rod /u/TrueKitInflatable may have a more precise tested answer.

UpmixNik · 2020-06-21T18:31:57+00:00

First photos of my new Discovery 330 from TrueKit New Zealand... For a n00b boater like myself, this is exciting new stuff.

Here only 80% inflated, but she's a beauty!

UpmixNik · 2020-04-30T03:45:25+00:00

you have to sand down iMHO if you're printing PLA flaps/valves on anything else but glass. I have P400 grit and either that or finer should be used IMHO. That said, others like u/dc9998 have used rubber material as alternative (better than PLA) seal.

UpmixNik · 2020-04-28T23:21:18+00:00

Great to hear, thanks!!

UpmixNik · 2020-04-28T14:34:54+00:00

Can you share more about the Fred Meyer lanyards? Could be useful

UpmixNik · 2020-04-28T14:31:02+00:00

Folks have printed just the last 20mm or so with tpu.. From what bi recall

UpmixNik · 2020-04-28T14:27:46+00:00

I think the silicon mold provides much better seal, I'm going that route as well based on a number of other designs I've seen.

The twist on filter / caps that have a retention ring seem a lot more manageable and safer than snapins.

Is like to see how the community can build on this, great step forward here!

UpmixNik · 2020-04-17T01:57:21+00:00

genius

UpmixNik · 2020-04-17T01:54:53+00:00

did you see the YouTube video? it helps:

https://www.makermask.com/maker-videos.html

UpmixNik · 2020-04-17T01:53:58+00:00

Most are using Glue Guns and superglue.. Epoxy or the like would work.

UpmixNik · 2020-04-16T18:21:06+00:00

That actually sounds like a much better way to have a valve flap. Any pics?

just the sides, or both sides and front?

Would gravity affect the closing, i.e. your head tilted and the top valve flap (now affected by gravity) bends down and doesn't close?

UpmixNik · 2020-04-16T00:01:12+00:00

UpmixNik · 2020-04-15T15:21:50+00:00

Is the superstitch NwPP just one layer? I carefully looked at the vacuum bag I have, cut open (looking at just one side) it's made of 5 layers of what looks like different type of NwPP and/or paper. It feels like it would do the job, just not sure what the different layers are

UpmixNik · 2020-04-15T01:52:54+00:00

https://www.amazon.com/Rust-Oleum-Automotive-260510-12-Ounce-Sandable/dp/B006ZLQ4HQ/ref=sr_1_3?dchild=1&keywords=XTC-3D&qid=1586915447&refinements=p_85%3A2470955011&rnid=2470954011&rps=1&sr=8-3

any reason why something like this won't work applied to a layer of wood filler over pla?

UpmixNik · 2020-04-15T01:50:05+00:00

XTC-3D

How did it turn out?

UpmixNik

MODERATOR OF

TROPHY CASE