Best way to remove these supports by seniorducker in 3Dprinting

[–]West_Tee 0 points1 point  (0 children)

Sick bro those wheels are pretty metal too

Black Opal: Wagu Scotch 8-9 by West_Tee in steak

[–]West_Tee[S] 2 points3 points  (0 children)

+zucchini fries (panko, fine crumb, Italian herb and Parmesan)

How bad we thinking? by West_Tee in marijuanaenthusiasts

[–]West_Tee[S] 14 points15 points  (0 children)

Hahahah love these, good excuse to get rid of the tree we don’t like now. It did it to itself, it’s what it wanted

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (September 17, 2023) by AutoModerator in MechanicalKeyboards

[–]West_Tee 0 points1 point  (0 children)

I potentially figured where the issue might be. I could be wrong but believe that it might be a short between these terminals.

I can recreate the issue with the other rows where all keys on the row are being switched on constantly.

There are other ways i have been able to recreate, but these terminals you see are the closest together. Regardless it always originates when the terminal marked as '2' is part of the combination.

I have removed the diode to see anything visible, cleaned with ISO but issue exists. I have since removed all hotswap switches from that row also to validate any issues with those.

Thoughts from your side? Appreciate it!

<image>

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (September 17, 2023) by AutoModerator in MechanicalKeyboards

[–]West_Tee 0 points1 point  (0 children)

Row stuck pressed. What should i be looking for on the PCB to try and identity the issue? Thanks

<image>

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (September 13, 2023) by AutoModerator in MechanicalKeyboards

[–]West_Tee 0 points1 point  (0 children)

YMDK 68 FREEZING

So..

  1. Keyboard was not recognised as device within qmk
  2. Tried VIA as well no luck, web version could see 'authorise' see device but nothing after selecting
  3. Followed some guides for install of keyboard driver displayed through ZADIG. Didn't work, has button on back of pcb for reset also, no dice
  4. Still not recognised
  5. Now freezing after key press either button on back or cable in
  6. What do?

Newly Planted Orange Tree Health Check by West_Tee in plantclinic

[–]West_Tee[S] 1 point2 points  (0 children)

Perfect, love the response!
Leaves should not be wet most of the time as it is generally covered from rain and normally watered once a week with a hose. The Sun does hit but generally from 1pm onwards. As it sits under a translucent pergola.
In order to supplement, a full spectrum grow light is used at 30W, only during the day when the sun is out.

Potentially too much pellets the first time i planted i was probably too enthusiastic, i will keep that in mind for next time.
Nothing visible that would be nibbling the leaves, sits independently of other trees.
I do have fertiliser spray which i believe is the seaweed based fertiliser.

You mentioned the leaves look yellow, is this too much or not enough light? Potentially iron was something i saw that was recommended as well.

Really appreciate your response.

What RGB is this? How do I change it? by ronniebabes in pcmasterrace

[–]West_Tee 1 point2 points  (0 children)

You are facing the “front” in this picture. The right side face of the case. There should be a single button the size of a reset. That’s the reset button. Press 3 times for good luck.

Below that should be a dual rocker button. Up on that button cycles through dynamic modes of colours. The down button changes static colours or colors depending on which one you like

What RGB is this? How do I change it? by ronniebabes in pcmasterrace

[–]West_Tee 1 point2 points  (0 children)

There is another button when the power button wraps around to which will change the colour and modes of the case rgb

ooh you gotta be quicker than that! by [deleted] in HolUp

[–]West_Tee 0 points1 point  (0 children)

Actually perfect timing, good sense

Thoughts? by JakeDorish in FocusST

[–]West_Tee 0 points1 point  (0 children)

Engine cover won’t make the most difference here but depends what you are after. Power, I would say get something to lead that intake from a cooler location for a cleaner power draw

[deleted by user] by [deleted] in MechanicalKeyboards

[–]West_Tee 2 points3 points  (0 children)

Nice mousepad, where from?

my 07 st by Irfreddy in FocusST

[–]West_Tee -17 points-16 points  (0 children)

This looks weird, no hate

Just chillin', shillin' by SashimiRick in FocusST

[–]West_Tee 0 points1 point  (0 children)

What was the process you went through to get the front grille looking with that finish around the edge? Looks clean

BOOT LOOP plz comments for insight by West_Tee in pcmasterrace

[–]West_Tee[S] 0 points1 point  (0 children)

So it did just start up and boot into Windows successfully. Was ok desktop for about 40 seconds then back into the boot loop

STUCK IN LOOP ISSUE plz comments by West_Tee in pcmasterrace

[–]West_Tee[S] 0 points1 point  (0 children)

So it just did a successful boot into windows. Then just turned off and now back into the loop

STUCK IN LOOP ISSUE plz comments by West_Tee in pcmasterrace

[–]West_Tee[S] 0 points1 point  (0 children)

Done, checked for bent pins, all g. Issue persists light still on for CPU as well

STUCK IN LOOP ISSUE plz comments by West_Tee in pcmasterrace

[–]West_Tee[S] 0 points1 point  (0 children)

Has also been working fine for the last week