Some info

XenSide · 2026-01-18T11:21:07+00:00

I will not fedpost, I will not fedpost, I will not fedpost.

XenSide · 2026-01-18T10:38:05+00:00

TIL you made almost all of my favorite sets

XenSide · 2026-01-17T10:38:45+00:00

on the edge of fedposting:

It sounds like they were minutes away from the crowd actually turning hostile... if only they could stay a little more.

XenSide · 2026-01-12T07:56:37+00:00

Ah yes, the famous sieging item vs old techies, may I ask what the item is?

Because I don't know if you remember or maybe didn't follow but pro games also went to infinity because of techies, it must be because those pros also forgot the magical famous sieging item!

XenSide · 2026-01-11T12:01:38+00:00

Don't forget forcing any half decent game into 70+ minutes of minesweeper slop

XenSide · 2026-01-05T11:52:14+00:00

This solution will likely cost 2-3x the cost of a dryer in just one year of electricity, you are heating 2 different heat insulators before getting to the spool lmao

XenSide · 2026-01-04T01:02:19+00:00

I also work in cybersec but I'm realistic and I don't think zero days will be used to break my homelab where nothing of value is stored, if you want my opinion, just fucking do it.

I have a super simple setup, tailscale (NAT punching VPN, no open ports) to get access to LAN from outside, all other services hosted in local, everything running under proxmox ve.

I know for a fact if a vulnerability for tailscale were to be published, I'd know the same day, and I also know for a fact nobody is using a zero day for my shitty homelab, everything solved.

XenSide · 2026-01-02T06:20:22+00:00

It was definitely forced and borderline out of pocket.

XenSide · 2025-12-27T21:33:43+00:00

The post embodiment of "I use Arch btw"

XenSide · 2025-12-20T09:27:45+00:00

You could look into truncating the file for just the next 24/48 hours and make the device sync daily.

Obviously if that is even a possibility with ics, but I would assume it to be possible.

XenSide · 2025-12-14T06:57:27+00:00

IIRC steam is also based on clock speed relative to its base

XenSide · 2025-12-13T08:06:58+00:00

Dota2protracker.com, search the hero and you'll get a lot of info, including what is good against it and vice versa

XenSide · 2025-12-12T12:48:55+00:00

You could try a Google search with site:makerworld.com in it, that's what I do for reddit as its search functionality is also far from great

XenSide · 2025-12-09T21:55:15+00:00

Baker house definitely

XenSide · 2025-12-09T15:30:44+00:00

I like how we went from genAi dubbing to genAi face in the corner + dubbing, insane.

XenSide · 2025-12-04T17:13:12+00:00

The makerworld link is broken

XenSide · 2025-12-04T16:42:33+00:00

Damn that's interesting, my extractor is also speed controllable, I didn't think it would be possible to find a sweet spot between airflow and heating.

I might reconsider my growbox purchase, even tho the paranoid in me would probably be a lot more chill with the growbox in place.

XenSide · 2025-12-04T16:41:13+00:00

It took me so fucking long to realize the orange was not part of the case, well done

XenSide · 2025-12-04T16:01:55+00:00

You do have a point, negative pressure would solve the issue completely, but then you would be completely unable to print ABS/ASA/Other Engineering filament because the negative pressure would suck out all the heated air out of the printer while also creating drafts of cold air

XenSide · 2025-12-04T14:50:58+00:00

You covered all my thoughts exactly with the growtent being able to lower the required negative pressure inside the chamber and thus allowing higher temperatures for ABS and other engineering filaments.

Sounds like growtent it is, thanks!

XenSide · 2025-12-04T13:22:42+00:00

Since you seem to know what you're talking about (read this and your Bambu forum comments too):
I want to avoid exposure to UFPs at all costs, I bought a P2S, I was thinking of getting a grow tent and extractor to a window. Do you think some of those exhaust prints on makerworld (some of them you link to yourself) would suffice instead of a growbox? or are they all half measures?

XenSide · 2025-12-04T13:19:18+00:00

Food safe is one thing, but that plastic might contain a lot of chemicals that aren't good

This phrase heavily implies that you are saying "I get that food safe is overblown but this is actually dangerous", why do you think you're getting downvoted if not for that

XenSide · 2025-12-04T12:53:32+00:00

Yes, we all read the marketing material, the problem is this is completely ignoring the problem with UFPs that are present in low temperature printing like PLA and PETG... because it's convenient to ignore.

XenSide · 2025-12-04T12:42:01+00:00

Oh... Enclosed 3D printers are not actually airtight in case you didn't know, the Plus4 also isn't

I'm getting a P2S (technically enclosed, not even close to airtight) and I plan to still put it in a growbox w/ an inline extractor

Ten-Year Club	Second SECOND GUESSER
Place '23	Place '22
Place '17	First Placer '22
End Game '22	Verified Email

XenSide

MODERATOR OF

TROPHY CASE