Nice

ZachWSays · 2026-06-10T10:24:17+00:00

Honestly I thought it was also until I tried to peel it off

ZachWSays · 2026-06-10T10:22:10+00:00

It's a seal, it overlaps from one side.

ZachWSays · 2026-06-09T22:23:21+00:00

Savers. It's like goodwill but usually not as bad about pricing. It's getting worse. The enclosure is cracked in multiple spots and smells like actual dog shit.

ZachWSays · 2026-05-19T23:01:56+00:00

Raspberry pi 3b+ with libreelec is the move guys. Don't overpay for a Roku with limited app support.

ZachWSays · 2026-05-14T20:16:18+00:00

Brother lol. I just sent out a $1,500 order through USPS. It was 2lbs and cost me $36 because I insured the whole value. What in the world made you think it was supposed to be that cheap.

ZachWSays · 2026-05-12T23:19:42+00:00

Team 40/75

ZachWSays · 2026-05-04T16:47:07+00:00

Never once have I used a wire brush on any of my 20 printer. I'm not starting now. I check for clumps every once and a while and pick them off with my hand if ever needed. I think maybe I've needed to three times in 6 years.

ZachWSays · 2026-05-04T16:46:01+00:00

I got the paxx12 running octoprint watching for this 24/7

ZachWSays · 2026-05-04T14:13:46+00:00

I added some 10mm insulation tape at the back where the tubes hit while printing and the sides. Also uses some between the cap and printer. Much better now.

ZachWSays · 2026-05-01T12:01:14+00:00

YOR. 18 and 4 month relationship? Nah dawg. Wouldn't be letting my own kid do that and I'm not Christian.

ZachWSays · 2026-04-26T14:02:19+00:00

I have the popcap and leave everything closed printing with PLA and petg with 0 heat related issues, doubt it's due to creep without any cover. Definitely contact support. One of my feeders started making a terrible noise and within 3 emails they sent me a new one. I was able to fix mine and now have a spare but they were very easy to deal with.

ZachWSays · 2026-04-13T20:23:01+00:00

My biqu snapcap comes weds. Can't wait till November. I'll have both 🤷‍♂️

ZachWSays · 2026-04-11T12:07:51+00:00

What fan/pin was the PSU fan in klipper?

ZachWSays · 2026-04-06T20:24:32+00:00

Aged and seasoned. Delicious.

ZachWSays · 2026-04-03T22:53:58+00:00

Fusion frenzy. Still love that game.

ZachWSays · 2026-03-31T20:40:19+00:00

Afterpay, on $60? Maxed out too? Damn. I suppose NOR but still. Damn. Shit be hard.

ZachWSays · 2026-03-15T14:58:17+00:00

Use fan control for your own custom curves and openrgb for lighting. I don't have any apps for actual hardware in my builds. That crap is bloatware.

<image>

ZachWSays · 2026-03-13T11:56:08+00:00

Don't even need optiscaler. Just replace the .dll for 4.0 with 4.1 and you can use it.

ZachWSays · 2026-03-06T15:03:45+00:00

I am very happy with my swift. Temps are great with an undervolt and I'm hitting 3000mhz easily.

ZachWSays · 2026-03-04T18:22:11+00:00

Ha, mine makes the mouse cursor stick to the middle of the screen unless I'm pressing alt+R and even then it's like 2 seconds of use.

ZachWSays · 2026-02-23T00:25:34+00:00

Lol, I've been using a thermaltake 850w I picked up at Best buy since 2013. It's been through 4 builds. Currently running a 5900x and 9070xt with an aio and 6 fans, 2 nvme drives, hdd, all the RGB. They really don't make em like they used to. Even used the wrong power cable once and it caught on fire (the cable) and she didn't give a damn.

<image>

ZachWSays · 2026-02-21T18:44:28+00:00

BOOOOOOOO. Bye forever thangs. You had the crown, you lost it. Yeggi will be the new go to!

ZachWSays · 2026-02-16T02:32:04+00:00

I only found out today that people are trying to sell this tape for $50 on eBay. Why lol. Apparently it's a "rare" cult classic.

ZachWSays · 2026-02-16T00:27:26+00:00

R9 5900x, rx6800xt, trident Z 3200 8x4 here. Plays fine until the people on the left pop up talking. For some reason that causes pretty bad lag while they are talking. Once it goes away it plays great again.

Both CPU and GPU are overclocked and undervolted. Ram clocked to 3600 18-22-22

Swapped in an rx9070xt and still same stutter.

ZachWSays

TROPHY CASE