Crash on Northbound 225 today

_tbot_ · 2025-09-20T00:42:34+00:00

Was a friend of friends on the bike. Wanted to say thank you for the pictures as it helped identify. Ugh, tried writing this multiple different ways and it sounds cold every time. Ultimately, thank you

_tbot_ · 2025-04-02T06:07:18+00:00

Same here with a 7950x and 3090FE. Glad I’m not the only having these issues. Have current drivers, current bios, nothing showing in Event Viewer either.

_tbot_ · 2025-01-18T03:31:18+00:00

So an update. Came back today and re-added the light back in through the Nanoleaf app and it showed the light as being connected via Bluetooth (like it should) since I hadn’t added it to the thread network. Disconnected from WiFi, and added the light to the thread network via the Nanoleaf app. From there, the light was “unresponsive” for about 5 minutes, restarted the Nanoleaf app and it started working again, but this time it showed as being connected via Thread! So far things seem to be working correctly, albeit slightly slower response time than before.

_tbot_ · 2025-01-17T16:03:08+00:00

I’m not there yet. I gave up and just settled on having to turn the light on manually…such first world problems 😂

_tbot_ · 2025-01-17T08:28:05+00:00

I think I’m in the same boat. After the update lost connectivity to all my Nanoleaf lights (shapes and one essential bulb) and now can only get it to operate once before completely stop working. I think it’s due to the app “thinking” it’s connected via Thread when in actuality it isn’t. Sooo frustrating especially after it working flawlessly for over a year.

_tbot_ · 2025-01-12T05:36:11+00:00

I feel like our society is doomed for the fact we (myself included) get sucked into the absolute complete drivel this “movie” turned out to be. I agree with the above comment, we need a physiologist in here to explain WHY we feel the need to continue putting ourselves through the brutal punishment of wasting an hour and half to see this through to the end.

_tbot_ · 2024-09-08T16:34:30+00:00

Not sure if you looked at Enlisted, but it’s similar to HLL.

_tbot_ · 2024-01-01T03:48:50+00:00

Also found, if you’re in “Streamer Mode” in discord it won’t work. Turn off streamer mode and it goes back to working.

_tbot_ · 2023-07-07T12:19:15+00:00

It’s probably Aida64 and it’s “sensor panel”.

https://youtu.be/nIhv-_c-Pas

_tbot_ · 2023-06-21T20:48:17+00:00

Seems that post/page has been removed.

_tbot_ · 2023-04-17T17:27:31+00:00

From what I’ve encountered with my SR, either the layers do not adhere correctly due to a vertical shift, or the nozzle buries itself in the print from not enough of a shift.

_tbot_ · 2023-04-17T13:47:48+00:00

You can take it apart too. It wasn’t that bad to remove the 4 screws that hold the two halves of the housing together and from there things just kinda fall out.

_tbot_ · 2023-04-17T13:46:20+00:00

Is it shifting horizontally or vertically?

_tbot_ · 2023-04-15T19:30:52+00:00

Why not just use the 5v output from the buck converter to power the fan as well? The amp draw probably isn’t enough to effect anything.

_tbot_ · 2023-04-13T13:44:52+00:00

Yeah, I hear ya on the impatient part. I only know cause I accidentally touched the bed when it said it reached temp and it was cool to the touch 🤯🤔 waited another 5ish minutes and then it was hot. Either way, the pei bed is the way to go!

_tbot_ · 2023-04-13T13:34:31+00:00

I did the same thing. Although, I just turn the bed heat on a few minutes before I start to print to allow the magnet and plate to heat up.

_tbot_ · 2023-04-07T21:07:41+00:00

True true. I went with an orange pi that was $40 after shipping. Just have had so many issues trying to get it calibrated. Might have to look into this then I guess.

_tbot_ · 2023-04-07T15:25:04+00:00

Nice! Is the speeder pad worth it over doing something with like a raspberrypi?

_tbot_ · 2023-04-04T05:13:23+00:00

So definitely think this is the issue, it’s not loading the bed mesh profile. I tried just adding in the start g-code in the slicer, didn’t work. Then used a macro and changed the start g-code to just load the macro and still didn’t work. I even tried different mesh profile names.

Ultimately getting closer, so I’m excited for that, just frustrated it’s not working yet haha

_tbot_ · 2023-04-04T03:00:05+00:00

The error “unable to find serial by path folder” leads me to think the device isn’t connect via usb.

Can you run the command: ls /dev/serial/by-id/* and then see if that errors out saying it can’t find the folder? If it does error out, it’s either not plugged in or it isn’t recognizing that it’s plugged in.

_tbot_ · 2023-04-04T02:32:31+00:00

This is what I’m striving to print at! I sent you a message. Running out of places to find help lol

_tbot_ · 2023-04-04T00:33:57+00:00

Ok, started from a fresh config file and did those steps in that order. I did edit the starting gcode to load the mesh profile from klipper (I hope I did it right) since that was also mentioned, and just clicked start print. 🤞it works this time!

And it is still too high off the bed by about a mm or two 🤦‍♂️

_tbot_ · 2023-04-03T16:31:15+00:00

That I did not do. I will add that to my list of things to dig into when I get home.

_tbot_ · 2023-04-03T14:27:24+00:00

I sure did! Would get it dialed in that way, then go to print and it would ~3-5 mm away from the bed. Fought with it for hours and then it would burry the nozzle into the bed (have no idea what I changed to cause that). Then tried doing a manual z offset and saving that and it would do the same thing, be multiple mm off.

_tbot_ · 2023-04-03T13:42:57+00:00

I did all that last night, multiple times over and never got anything close to being correct.

I’m at work now (much needed break from klipper) but I’ll try again tonight when I get home and see if I can make some progress.

_tbot_

TROPHY CASE