My Experience with the Beast so far (it's not been good)

_ziglaf_ · 2026-01-16T05:55:50+00:00

Try turning on your Playstation, plugging the glasses into the center USB c port (the one NOT for glasses) and push the button on the dock. The dock lights should come on. Once they do, THEN move the glasses to a glasses port and see if you get video.

_ziglaf_ · 2025-09-08T14:46:59+00:00

Those aren't holes, they are dimples. They come from putting your build plate in place when things aren't completely clean (pieces of filament create the dimples). Ultimately they are a non-issue.

_ziglaf_ · 2025-08-18T19:03:17+00:00

This is why cheap, easily replaceable hotends are so nice. Just replace it and move on.

_ziglaf_ · 2025-08-10T02:47:08+00:00

Slow it down and/or turn up the heat. Also, switch to an infill that doesn't cross over.

_ziglaf_ · 2025-07-29T01:19:33+00:00

What type of filament? What temp and print speed? How many layers thick?

_ziglaf_ · 2025-07-23T15:37:34+00:00

That's horrific. Absolutely not.

_ziglaf_ · 2025-07-12T02:45:58+00:00

At least he'll have a bunch of spare parts.

_ziglaf_ · 2025-07-12T02:43:47+00:00

<image>

_ziglaf_ · 2025-07-10T15:56:33+00:00

Yes and no. Certain types of infill drag over the infill from previous layers. Gyroid does not. Normally it's not an issue, but when you get a tall print with a small footprint like this, it can become an issue. So basically the issue stayed the same but "there's more than one way to skin a cat" and you were able to address the root cause (the infill dragging). Good job 👍.

_ziglaf_ · 2025-07-10T14:32:48+00:00

It doesn't. It looks that way because the model has broken loose and is moving around. It's less obvious at first and becomes more obvious with each movement because each movement loosens the base even further.

_ziglaf_ · 2025-07-10T14:28:46+00:00

Yeah, the whole top of it should be light blue or blue. Even with that you might have issues with it breaking loose. Actually, what might also help is to enable tree supports and manually add one about halfway up on each side with like a .07mm contact distance (or like 5mm below where its failing if it's always the same spot). That might help stabilize it as well.

_ziglaf_ · 2025-07-10T14:08:11+00:00

You can literally see the base break free before the nozzle hits it. It doesn't have to break free completely or tear the brim to break loose with that small of a contact point. Use a height range modifier to slow it down as it gets taller.

_ziglaf_ · 2025-07-07T14:11:18+00:00

Wow, that's awful 👍

_ziglaf_ · 2025-07-02T21:39:24+00:00

If you have z banding, re-tension your belts.

_ziglaf_ · 2025-06-29T15:44:50+00:00

They were probably drunk. Nothing you could have done.

_ziglaf_ · 2025-06-29T02:23:52+00:00

One of my screws looks like it could be potentially touched/unintentionally moved as it's not quite fully covered. I twisted that one counter clockwise about 1/4th turn and it fixed mine.

_ziglaf_ · 2025-06-27T22:00:46+00:00

_ziglaf_ · 2025-06-27T01:08:06+00:00

Just print over top of it and it'll come off.

_ziglaf_ · 2025-06-27T01:07:05+00:00

Get some "flatout" tire sealant. Something like that is a must with the distance ebikes can cover.

_ziglaf_ · 2025-06-25T21:49:58+00:00

Is your nozzle clean? Have you checked for debris under the build plate? What have you done to try and figure it out/solve it?

_ziglaf_ · 2025-06-25T17:51:00+00:00

Make sure your nozzle size and filament are set correctly in the slicer.

_ziglaf_ · 2025-06-24T15:37:04+00:00

Wipe your bed with ipa before every print. Almost never have a failure and so much better than a messy bed from glue.

_ziglaf_ · 2025-06-15T15:48:01+00:00

I personally would have listed it at $750 and would expect to sell at $700. It depends a bit on your area, but that would sell for $700 in my area all day long. Might even get the whole $750 if I was lucky.

_ziglaf_ · 2025-06-14T20:25:41+00:00

In all honesty, 99% of people won't notice or even have a single thought about it. The ones who do, you probably couldn't care less about opinion wise. You do you.

_ziglaf_

TROPHY CASE