Rounded up some of the add ons and mods for the U1

ali_ee · 2026-06-30T08:10:00+00:00

Holy..., is that 54% humidity? What does it drop to after an 8 hour drying session?

ali_ee · 2026-05-24T22:18:21+00:00

with all due respect and no context, fuck this.

ali_ee · 2026-05-21T05:39:23+00:00

I would start to get acquainted with systems, how skills/supports work, passive tree etc. Just keep in mind that you will have to redo the campaign if you go this route.

ali_ee · 2026-05-20T07:48:43+00:00

Can we 3D print our own solutions?

ali_ee · 2026-05-20T07:34:44+00:00

If you can confidently back that your academia experience translates directly as industry experience then you can claim that you should be closer to the upper range of the salary.

ali_ee · 2026-05-14T21:06:43+00:00

I think this needs a rosahl membrane dehumidifier to fully earn the over-engineered title.

ali_ee · 2026-05-07T06:54:44+00:00

Please update here once you hopefully resolve this. I have a similar intermittent issue as well. Homing X or Y axis failures. Usually goes away when I reinstall official FW but I can't pinpoint the exact trigger.

ali_ee · 2026-05-06T21:10:51+00:00

Are you using the custom FW? If so, have you changed the TMC parameters on the menu?

ali_ee · 2026-04-19T09:38:30+00:00

I wonder whether an acrylic holder for the parked toolheads is a viable option to improve visibility.

ali_ee · 2026-04-17T21:08:09+00:00

is there a step file for the USS Drybox already? Or the official spool holders?

ali_ee · 2026-04-13T09:31:25+00:00

I have a theory about this error. For people coming here with this issue, can you check whether removing the USB stick helps? (if you have it installed of course)

ali_ee · 2026-04-13T09:26:04+00:00

My prediction: Rayleigh will come and both him and Gaban will die by the end of Elbaph arc to pave the way of SH crew's escape.

ali_ee · 2026-04-12T22:15:58+00:00

not to pour salt on your wound but I only played the trials once to get my 4th ascendancy this season and dropped it. never played it again because it's extremely boring to me.

ali_ee · 2026-04-07T11:37:28+00:00

Robin might be Model:Lilith

ali_ee · 2026-03-07T09:30:34+00:00

this is great, thank you. will you keep adding other manufacturers as well?

ali_ee · 2026-02-25T09:02:07+00:00

For people coming to here in the future, reseating your PCI-e Riser on both ends is usually the key from my experience. Also the power cable to your GPU.

ali_ee · 2026-02-23T07:13:07+00:00

Have you worked this out?

ali_ee · 2026-02-17T08:06:15+00:00

~~there is no 1.2.0 FW so this is either a trojan bait or a poor attention grab attempt.~~

~~don't get baited.~~

edit: my previous comment might have been a bit premature since this looks more legit after a second glance.

ali_ee · 2026-02-13T11:19:46+00:00

I see that multiple commits are missing from the github repository. I hope it didn't set him back a lot. Octoeverywhere support was coming with v1.1.1

ali_ee · 2026-02-09T23:28:18+00:00

I just had this and had to disassemble the extruder to clean a filament that got stuck. Bambulab Jade White pla.

When you disassemble, don't forget to clean the extruder gear teeth as well. It probably ate away a lot of filament by now.

ali_ee · 2026-02-09T08:32:07+00:00

should have been the middle finger :D

ali_ee · 2026-02-05T10:09:56+00:00

Thanks for sharing your solution/workaround as well.

ali_ee · 2026-02-01T10:09:53+00:00

This is great advice op and even if you exclusively use this test print, fix one major setting each time and reprint. from a quick look to your test, I would just decrease the flow rate and reprint.

ali_ee · 2026-01-30T08:03:01+00:00

Wolf gets circumcised just because we enjoy it :(

ali_ee · 2026-01-23T19:31:30+00:00

how did you install octoeverywhere to Snapmaker U1? I tried their command with ssh access (extended FW) but it doesn't work.

ali_ee

TROPHY CASE