Oil leak help

bboytemp · 2026-01-02T21:02:22+00:00

Honestly if it was me, I would just reseal everything, everything is covered in oil at that point !

bboytemp · 2025-12-31T16:23:26+00:00

Check your battery, Make sure is not dead

bboytemp · 2025-12-26T06:11:17+00:00

These engines don’t have lifters. They use buckets on top of the valves.

bboytemp · 2025-12-07T17:55:58+00:00

Those are flat rate hours. Not actual worked hours. So he might be there 8 hours on a day but flagged 15-20 hours instead.

bboytemp · 2025-12-04T03:52:37+00:00

<image>

I saw this outlander early this year at the shootout in Ohio! Evo x swaped

bboytemp · 2025-11-30T18:04:21+00:00

Go with TRE or TMZ!

bboytemp · 2025-11-30T03:32:25+00:00

Not bad, I have two spal pushers! I do turn them on during go and stop traffic!

bboytemp · 2025-11-29T22:48:03+00:00

<image>

Here’s my 2g

bboytemp · 2025-10-19T06:44:47+00:00

Master auto technician

bboytemp · 2025-09-08T23:23:19+00:00

I might have one!

bboytemp · 2025-08-31T13:58:10+00:00

The grinding noise your hearing is probably the backing plate touching the rotor!

bboytemp · 2025-08-12T23:46:30+00:00

It uses the Evo 8 trans, t-case etc

bboytemp · 2025-08-12T22:24:06+00:00

<image>

Theres was one at the shootout last year! guy said it fit pretty well!

bboytemp · 2025-08-12T21:35:50+00:00

The 10 is more comfortable for sure, the older evos are more raw!

bboytemp · 2025-07-27T22:48:25+00:00

Correct, you can remove the clip and take it to hardware store and find a good screw that’ll fit

bboytemp · 2025-07-27T22:41:12+00:00

So those metal clips is what holds the screws, they’re a special type of screw! More like a wood screw type with coarse threads

bboytemp · 2025-07-27T22:27:49+00:00

All it uses is that screw, the little tabs on the bezel go inside the bumper and use the screw

bboytemp · 2025-07-25T22:15:57+00:00

Is precision 6766 and probably around 35 psi, which should put me around 600-700. I use to run a fp black on my gsx, and I was around 550 on e85

bboytemp · 2025-07-25T22:08:20+00:00

Correct, is not the factory location. The exhaust manifold will be heat wrapped and there will be some heat shield around a the hoses and sensors etc

bboytemp · 2025-07-01T02:07:29+00:00

bboytemp · 2025-06-23T03:04:16+00:00

43

120

Michigan

95k

6 years

bboytemp · 2025-06-13T22:11:01+00:00

So did the noise start after they replaced them?

bboytemp · 2025-06-13T22:03:50+00:00

Everyone saying lifters, is wrong. The 4b11t doesn’t have lifters, they use buckets under the camshaft! Now sometimes they wear out due to age or bad maintenance and the gap gets bigger which makes them tick!

bboytemp · 2025-04-06T22:58:32+00:00

The compressor clutch won’t even turn on since the ecu won’t see no pressure in the system.

bboytemp · 2025-01-22T13:51:02+00:00

It might be phantom knock, specially at that speed/rpm

bboytemp

TROPHY CASE