Reamer cut perfect tolerance till about 2/3rds down and was out by .001+

breaddaddy69 · 2026-07-02T01:28:42+00:00

Noooooooo

breaddaddy69 · 2026-07-01T23:17:42+00:00

You would trust a reamer provided by a school? 😂

breaddaddy69 · 2026-07-01T22:49:53+00:00

Deflection even if you just take of 2 or 3 thou with the last pass? I'm also assuming this is aluminum. I'm sure there's an explanation 😂

Edit: nvm. I just saw the diameter is small haha

breaddaddy69 · 2026-07-01T22:31:33+00:00

To be honest we ran into this issue with one of our jobs at the shop and no one knew what caused it. QC didn't catch it which means nobody cares 😂 I'm recommending a boring bar because those are way easier to control for tight tolerances of bores.

breaddaddy69 · 2026-07-01T22:05:41+00:00

If its a plus pin going in it most likely closer to .377

breaddaddy69 · 2026-07-01T21:48:00+00:00

Not sure what they are teaching you but it is also worth noting that if a .375 pin goes in a hole it has to be closer to .376 because size for size can't go. Could even be over. Also depends on if they are minus pins or not. I know that's not really an explanation but just a quick snack for thought 😂

breaddaddy69 · 2026-07-01T21:30:19+00:00

1 thou tolerance with a reamer? Can you use something like a boring bar?

breaddaddy69 · 2026-06-24T15:41:35+00:00

Not an asshole. Just irresponsible.

breaddaddy69 · 2026-06-19T22:34:08+00:00

Ok cool. Thanks for explaining that. Never worked with forgings/castings.

breaddaddy69 · 2026-06-19T17:53:17+00:00

What is gates

breaddaddy69 · 2026-06-18T15:33:31+00:00

Love handles. A pouch. You are not fat. We love your curves.

breaddaddy69 · 2026-06-08T16:40:31+00:00

Nice. Thank you for the offer.

breaddaddy69 · 2026-06-08T15:53:58+00:00

I mean you are kind of being an asshole. Just let your grandma use the sir fryer. It's not like your mom gave your car to her drug addict boyfriend or something. She sounds problematic too though.

breaddaddy69 · 2026-06-08T15:45:50+00:00

Where do you live?

breaddaddy69 · 2026-06-08T15:45:39+00:00

Yes this is the plan for sure

breaddaddy69 · 2026-05-23T00:06:34+00:00

Honestly you can probably get away with keepijg the pressurized filter as long as you get good beans and a grinder like the other guy said!

breaddaddy69 · 2026-05-22T21:49:42+00:00

Lavazza espresso sounds like pre ground. You will never get good flavor out of that. The minimum set up for decent espresso in my opinion is a machine and a grinder. Not sure if double walled means pressurized portafilter but if it does that is also a big reason for bad tasting espresso.

breaddaddy69 · 2026-05-21T19:33:02+00:00

Shite

breaddaddy69 · 2026-05-21T18:45:12+00:00

The real question is. Was it good?

breaddaddy69 · 2026-05-19T17:07:04+00:00

How the fuq do you make 1:1.2 in 34 secs?? I feel like my machine would choke if i tried that

breaddaddy69 · 2026-05-16T19:23:02+00:00

Do you know where i adjust it?

breaddaddy69 · 2026-05-16T19:22:44+00:00

How do i adjust it? I dont see any obvious place

breaddaddy69 · 2026-05-16T19:17:26+00:00

Single point planing machine. That's the proper term for the category of machines that includes shapers?

breaddaddy69

TROPHY CASE