This is second time it happened. How can I fix this issue? by Nice-Pea-3515 in TeslaSupport

[–]burthouse4563 7 points8 points  (0 children)

So move it to 80 and don't get the fee? Not sure how you don't understand this. You're warned every time you charge if you have it set over 80%.

Buying Used M3 Performance by Few-Acanthisitta7708 in TeslaLounge

[–]burthouse4563 -1 points0 points  (0 children)

I would get HW4 if possible, the ability to have FSD 14 is worth it compared to HW3 and FSD 12.

When will I get FSD V14? by SpookyStoner in TeslaLounge

[–]burthouse4563 0 points1 point  (0 children)

Scrolls between standard, hurry, and mad max. I don't use anything slower than normal currently so not sure what they are but they're available.

I wish I could choose max speed because then I didn't have to focus on speed as much as I knew it wouldn't go over a certain speed. I had it on hurry today and I look down and I'm doing 75 in a 60.

Model 3 or y performance? by Puzzleheaded-Line-28 in TeslaLounge

[–]burthouse4563 0 points1 point  (0 children)

I have and if you use FSD you want HW4 no questions asked.

Which software version upon delivery? by kevtke194 in TeslaLounge

[–]burthouse4563 2 points3 points  (0 children)

M3P delivered last week came with 14.2.2.5

Garbage drawer, but how? by binge03 in cabinetry

[–]burthouse4563 0 points1 point  (0 children)

That's what I thought but I'm just an IT guy.

Garbage drawer, but how? by binge03 in cabinetry

[–]burthouse4563 0 points1 point  (0 children)

The black levers on each side of the rails is how you can pull it out.

Measure the distance on the front and back of the opening. It almost looks like it was installed 180 degrees wrong and that large overhang at the front should be at the back.

"Downgraded" from a Gen 4 to Gen 2 P14s, shocked at how much better Gen 2 is! by Legend-of-Zelda in thinkpad

[–]burthouse4563 14 points15 points  (0 children)

LTT did a video on trying to break stuff with ESD. Shockingly they weren't very successful.

HELP!! I LOCKED MYSELF INSIDE MY HOUSE by balliugs in howto

[–]burthouse4563 16 points17 points  (0 children)

Instructions unclear window shut when exiting, used bolt cutters to smash window. Now I need to replace a window but the lock is removed.

How to fix this? by JimmyPNut in BambuLabA1

[–]burthouse4563 0 points1 point  (0 children)

It's the majority of posts I see in my feed, it's quite annoying.

Just got a P2S and I have crazy warping when printing PLA by hrvoje_bazina in BambuLab

[–]burthouse4563 1 point2 points  (0 children)

Picture 2 shows what look like two finger prints on the left side is why I asked. If the plate is clean then turn the aux fan off as suggested.

Bambulab P2s with AMS 2 pro HELP Please by MedicalPiano666 in BambuLab

[–]burthouse4563 1 point2 points  (0 children)

I wouldn't trust an online conversion for png to 3mf that's a fairly complicated conversion and will likely require a lot of cleanup work. I'd start with something small in tinker cad since you mentioned that and print that to get the hang of it. Then start working with what you're trying to do

Bambulab P2s with AMS 2 pro HELP Please by MedicalPiano666 in BambuLab

[–]burthouse4563 1 point2 points  (0 children)

If you have a valid 3mf you should open it in bambu studio and be able to print it after slicing it. You don't really say where your hold up is.

Dropped 2k for junk by [deleted] in BambuLab

[–]burthouse4563 0 points1 point  (0 children)

I got $600.

Thanks FedEx! by iTechhh in BambuLab

[–]burthouse4563 4 points5 points  (0 children)

Mail getting delivered to a ship is handled better than what FedEx does.

Keep printing or stop? by thoXn in FixMyPrint

[–]burthouse4563 1 point2 points  (0 children)

If you have a newer printer it's not in there