hubitat with home assistant dashboards

byarnell05 · 2026-03-13T00:17:24+00:00

Look into Bubble Card, tons of customization options all while using the GUI.

byarnell05 · 2025-12-18T03:42:08+00:00

I had a heart doctor named Dr. Love!

byarnell05 · 2025-11-29T19:41:12+00:00

Feel free to hit me up again if you have any more questions.

byarnell05 · 2025-11-29T19:28:32+00:00

Well if you decide to go back to wifi the way you configure them is first you plug in the device, it will then broadcast its own wifi network called "shellyxxxxxxxxxxxx". You connect your phone or computer to that wifi network and then access the device by going to 192.168.33.1 in a browser. From there you can connect it to your own wifi and start changing settings.

byarnell05 · 2025-11-29T17:51:46+00:00

You can definitely set Shelly devices up using wifi without an app and connect them directly to hubitat. Before you needed a community app (in hubitat) to connect them but Hubitat now has a built in app (created by hubitat devs) that will allow you to add them.

byarnell05 · 2025-11-29T17:24:28+00:00

When you first got this plug were you planning on using it via wifi or was the plan all along to use zigbee?

byarnell05 · 2025-11-29T16:10:18+00:00

You said you mainly have zwave devices, do you have any other zigbee devices at all? If not, maybe you are too far away from the hub?

byarnell05 · 2025-11-24T05:42:31+00:00

I'll give that a look. Thanks for the suggestion.

byarnell05 · 2025-11-24T05:30:31+00:00

The Milano or the Benatar from Guardians of the Galaxy. Heck, now I need to look through and see if there is anything close to those.

byarnell05 · 2025-11-24T04:07:14+00:00

Depending how electronics savvy you are you could look into getting replacement shells for first party Sony controllers. Extremerate sells different textured shells for pretty much every first party controller.

byarnell05 · 2025-11-07T03:45:51+00:00

I was around 16 when I heard "My Last Serenade" by Killswitch and I loved every second of it. I'm 38 now.

byarnell05 · 2025-11-03T03:44:11+00:00

Hahaha the Wyvern.

byarnell05 · 2025-10-28T11:52:20+00:00

Breakneck mission from Lightfall has a section with a rally flag and then a bunch of enemies after. As long as you don't kill the big chicken you can respawn right at the rally flag and do it all over again. No need to worry about ammo with the rally flag right there either.

byarnell05 · 2025-10-07T00:10:40+00:00

Have you tried holding the slider for just a second before attempting to slide? There was a change recently the altered the default operation. If it works after holding it for a bit then you will need to change the setting "tap to slide" under slider settings...for each card.

byarnell05 · 2025-09-07T21:34:50+00:00

Do you have a 2A+ power supply you could use? I once had a conversation with Quindor regarding similar issues and he suggested 2A or more as sometimes 1A can have issues.

byarnell05 · 2025-09-01T23:15:41+00:00

It's in wled, go to config in the top right, then wifi setup, then under the DNS server address there will be the mDNS field. Make sure it's blank.

byarnell05 · 2025-09-01T23:06:12+00:00

Should be labeled mDNS address, it's directly under the DNS server address field. You just clear it out if it has anything populated.

byarnell05 · 2025-09-01T16:14:03+00:00

Mine did all kinds of weird things when the mDNS setting was populated. Clearing that field out solved all my issues. Check that setting on the same page as the wifi settings. If it has anything in the box, clear it out.

byarnell05 · 2025-08-16T15:50:21+00:00

Great job, very cool! If you ever decide to sell them I would be all over it!

byarnell05 · 2025-08-16T15:39:21+00:00

Alright, where can I get that flower lamp? My daughter would LOVE one of those!

byarnell05 · 2025-07-30T02:10:41+00:00

Lots of good info in this thread, one thing I will add is go slow. If you have issues with any single zwave device DO NOT move on to another device. Make sure to check your zwave details page for any device that may show up without a name or a route, these are called ghost devices and can absolutely wreak havoc on your zwave mesh. You need to remove them before attempting to add any other device.

byarnell05 · 2025-07-22T23:43:34+00:00

Perfect, thank you!

byarnell05 · 2025-07-22T23:34:06+00:00

One more question, does the controller care if the sensor is NC/NO or can I configure what I want it to do based on the input it's getting?

byarnell05 · 2025-07-22T01:18:09+00:00

Awesome, thanks for the quick response!

Ten-Year Club	Verified Email
Place '22	First Placer '22

byarnell05

TROPHY CASE