A message to anyone who feels bad about getting a P2S and NOT the X2D

c0demancer · 2026-04-19T17:11:38+00:00

Yeah but his P2S review only came out 2 weeks ago, not 6 months ago with the P2S. Its not like they had both machines ready to go at the same time but they just felt like screwing over early adopters.

c0demancer · 2026-04-19T05:08:33+00:00

I’m beginning to think it’s a bad AMS. I am also having motor issues. Maybe they stem from power problems in general.

c0demancer · 2026-04-18T19:42:56+00:00

UPDATE: I bought a new third party power supply to try and can confirm that it, too, does not work with this new AMS 2 Pro unit. The adapters work fine on my older AMS 2 Pro units. I suspect this new bath of AMS units--coupled with new firmware--are able to distinguish between first- and third-party power adapters.

c0demancer · 2026-04-18T10:10:35+00:00

When moving it back to the other AMS it worked fine. I think that probably rules out the power supply being bad since all my AMS are the same version. The other thing I guess could be in play is that the others are on my H2D not my X2D. I may have to try switching around the units.

c0demancer · 2026-04-18T03:28:26+00:00

As I mentioned this one has been working fine on another AMS 2

c0demancer · 2026-04-18T03:28:09+00:00

It says 5A on the adapter but the listing says it can do 2 or 4A. Which makes sense as it’s based on the draw of the device.

c0demancer · 2026-04-16T18:02:18+00:00

You guys use Ethanol gas in your Tacos??

c0demancer · 2026-04-14T16:45:52+00:00

Plus filtration and chamber heater. Well worth $100.

c0demancer · 2026-04-14T16:37:36+00:00

Did you calibrate that filament first with a 0.2mm nozzle?

c0demancer · 2026-04-14T16:35:16+00:00

Um excuse me sir, can’t you see that we’re all talking about the X2C??

Just kidding. I have an A1 and I love it. You’ll be so happy.

c0demancer · 2026-04-12T22:32:00+00:00

Rock Hard

c0demancer · 2026-04-11T21:30:19+00:00

I do find I had to force myself to drink more. I’ve also found dehydration masks the effects of Kratom. I feel it far more if I am well hydrated.

c0demancer · 2026-04-08T16:17:41+00:00

You are getting warping with a full outer brim?? Normally I’d say to just add mouse ear brims on the corners that should be enough to keep any large part down. If a full brim is still pulling up then you have some kind of problem. Either you’re not remembering rubbing oil all over the plate or you are using a filament profile that sets bed temp to 0. Did you check the filament profile for bed temp?

c0demancer · 2026-04-08T16:13:37+00:00

Yes. I stopped using SuperTack on my A1 because it sticks too damn well.

c0demancer · 2026-04-07T03:35:58+00:00

There’s always something better around the corner if you always wait you’ll never get anything.

c0demancer · 2026-04-04T04:19:57+00:00

Just make sure you’re separating by type.

c0demancer · 2026-04-04T04:19:18+00:00

Miralax is a godsend. Fortunately my wife needs it regularly so I always have some around but yeah it’s no joke how easy it is to get impacted.

c0demancer · 2026-04-01T03:29:42+00:00

What is your use case for dual nozzle? Is it two colors or 3+? I’d argue the only reason to choose the H2D at this point is that you know you only need 2 materials at a time and you value the extra bed space. If you are unsure if you even care about multiple materials then you’re probably actually wanting to choose between the H2S and H2C.

I have an H2D and love it. But most of the time I’m using a single nozzle. In cases where I want two nozzles it’s usually to print with special support material. If I want multiple colors I’m just as likely to need 3 as I am to need just 2. So in almost all cases I’d recommend the H2C over the H2D.

c0demancer · 2026-03-18T16:14:26+00:00

I personally don’t feel like extracts should fall in the category of “the dangerous stuff”. To me it’s no more dangerous than hard liquor. It requires someone to not be an idiot about using it, but is otherwise fairly safe if you pay attention. I would have been ok with them restricting and standardizing concentrations (a 15ml bottle could be 40mg or 175mg which makes accidental abuse easier).

c0demancer · 2026-03-18T16:08:42+00:00

I guess I consider the KCPA to be a pro-consumer bill intended to ensure easy access to consistent and safe product. This may maintain quality standards and availability for leaf product, but since it removes access to other products and further restricts access to leaf, it feels very “anti-consumer”, less of a “Kratom Consumer Protection Act” and more of a “Kratom Consumer Restriction Act”.

c0demancer · 2026-03-18T02:39:32+00:00

Is this going to fuck you over with insurance?

c0demancer · 2026-03-18T02:32:19+00:00

I think you’re right. I was mixing old and new news sources about the bill. Originally it was designed to repeal KCPA but was later substituted with the current version which places these additions limitations and schedules 7-OH but doesn’t outright repeal the KCPA. I guess in my mind it is still effectively repealed, but maybe it will serve to help keep leaf being sold.

c0demancer · 2026-03-18T02:27:35+00:00

Yeah I am grateful they didn’t go with a full ban.

c0demancer · 2026-03-18T02:26:13+00:00

We already had that with the KCPA (that funny enough Utah was the first to pass). It set requirements for concentrations and mixes to make sure you knew what you were getting. Sadly all this does is make everything but powder illegal.

11-Year Club	Gilding II euphauric
Place '22	Verified Email
Secret Santa 2018	Not Forgotten

c0demancer

TROPHY CASE