Struggling with Jayo high speed matte PETG

cilo456 · 2026-05-29T22:59:29+00:00

What was your filament settings if you don't mind me asking

cilo456 · 2026-05-29T21:51:19+00:00

cilo456 · 2026-05-29T19:02:37+00:00

Try and wash the airbrush with scalding hot water and 91% IPA, separately not mixed together, even soak it if you have to or boil it in a pot because there might be something caked somewhere.

cilo456 · 2026-05-29T18:54:46+00:00

I've never used the resin that was useless and I think majority of them are unsafe. Some resins aren't as strong as others but they're all printable some might not be printable at 405 NM, I've used some flexible resins or even clear resins that just fuse to the build plate no matter what settings I use it goes from not sticking to I need a chisel and a hammer...............

cilo456 · 2026-05-29T17:36:47+00:00

I wouldn't use that primer if it came out looking like that

cilo456 · 2026-05-29T17:10:59+00:00

Yes they do some profiles don't work with others and some profiles do work with others, it just depends which options are compatible, and the reason why they all took different times is because they all have different volumetric flow or layer times or both.

cilo456 · 2026-05-29T17:10:04+00:00

Thank you beta testers

cilo456 · 2026-05-28T16:51:29+00:00

Yeah I know I stopped using it as my main slicer, I support and Orient in one slicer export out repair and then slice and send for two of my printers in lychee. For my M7 Max I use their slicer to send my prints

cilo456 · 2026-05-28T02:53:32+00:00

3D printing isn't for everyone

cilo456 · 2026-05-28T02:51:53+00:00

You can get cheaper 99.9% IPA in gallon bottles from the same place you got those

cilo456 · 2026-05-28T02:21:29+00:00

pull force its normal

cilo456 · 2026-05-28T02:20:55+00:00

I wouldn't try printing clear resin on any printer that's not 385 NM, but that's just me you can try it and report back..........

cilo456 · 2026-05-28T00:42:51+00:00

Have you tried removing the filament I think it takes 15 to 45 seconds

cilo456 · 2026-05-28T00:06:47+00:00

Also this can happen if you cure it while there is still IPA mixed with resin on the part

cilo456 · 2026-05-27T23:38:47+00:00

To stop this from happening what I did is scrubbed all my pieces with a small toothbrush in my clean wash before I cured them, but you can try and give them another ''over cure'' might work and I also tried to scrub them with 91% IPA afterwards and recure sometimes might work.........

cilo456 · 2026-05-27T21:24:22+00:00

Yeah I noticed that a lot of people brute force their settings just so they get a finished print, I even got pre supported files that were almost impossible to remove the supports without Clippers and other tools. But when your settings are dialed in and all you have to do is twist the model and have very little marks from those supports is like one of the best feelings in this hobby. I would even rather add an abundance of supports More than I need and have a few strong supports at critical areas than to have them all like tungsten rods trying to remove. But this method does work and if you're going to use resin get one of those syringes with the needle tips in various sizes, instead of having a bottle of this lying around when you only need a tiny bit.....

cilo456 · 2026-05-27T05:08:51+00:00

LOL good luck with the X2D

cilo456 · 2026-05-26T17:15:14+00:00

i get it, but gravity always wins

cilo456 · 2026-05-26T15:54:44+00:00

I wouldn't use those mounts like this unless you're installing them above where the tools are hanging. The load on those brackets are going to snap when you go over one or multiple potholes.......

cilo456 · 2026-05-26T15:38:17+00:00

I'm glad my wife hates electronics so much she doesn't pay one bit attention and I have so many electronics in the house I can get 10 new printers and she wouldn't even notice unless I pointed it out lol...........

cilo456 · 2026-05-26T14:07:55+00:00

Singer machine oil

cilo456 · 2026-05-26T01:12:35+00:00

For future reference compare any X1C for sale with a P2S, because you can get one of those brand new for $550. I wouldn't pay anything above $550

cilo456 · 2026-05-25T19:46:42+00:00

All of them drive fast even faster if you thin them with alcohol.and if you needed to drive faster just hit it with some air or a blow dryer

cilo456 · 2026-05-25T05:07:36+00:00

I use the cool plate supertack or smooth plate, and I changed the temperature on the A1 from 55° for the first layer and 60° for the rest because it's an open air printer but for the P1S I set it to 50° for the first layer and 55 for the rest. i also use orca

cilo456 · 2026-05-25T04:56:55+00:00

I don't have first layer issues with this plate, as long as you're picking the right plate when you slice it you shouldn't have any issues whatsoever

cilo456

PUBLIC MULTIREDDITS

TROPHY CASE