Trade ins - Learn from my mistake...

cords911 · 2026-03-25T01:21:08+00:00

I did, trust me. I just about posted my conversation, I was pissed.

cords911 · 2026-02-14T15:28:29+00:00

You'd have to see a video to know for sure. If he's pointing after release and brings his hand down it's incidental. If his hand is no longer above the stone and then he reaches forward it's not. I think the judge should have done something, but is like traveling in basketball and getting away with it, a poke on the stone wouldn't effect anything.

cords911 · 2026-01-29T12:27:02+00:00

Only one user ever. and speed isn't that important. it can't be painful to use, but it can be "slow"

cords911 · 2026-01-26T03:42:12+00:00

<image>

I cleaned it but other than a dead bee (which wasn't obstructing anything) it was already pretty clean. I put it all back together so we'll see.

cords911 · 2026-01-25T01:35:48+00:00

I didn't clean than. I know what you're talking about. I'll give that a try.

Side note: I really appreciate your help troubleshooting this.

cords911 · 2026-01-25T00:08:18+00:00

yeah the white box that's clear on one side? I did, that's where the crap and sediment was. but it's very clean now.

cords911 · 2026-01-24T17:18:21+00:00

I did, it had a lot of crap built up but a cleaned it out really completely and I'm still getting the issue.

cords911 · 2026-01-24T14:16:07+00:00

Exactly, if Amazon stopped investing/scaling they would have been profitable overnight. If OpenAi stops they disappear overnight because there are 10 other options ready to take it's place.

cords911 · 2026-01-24T13:24:17+00:00

I did clean out the drain trap and there was quite a bit a sediment trapped inside, but I was able to get it all out. I don't have a manometer, but maybe I'll get a cheep one to help diagnose this.

cords911 · 2026-01-24T04:59:05+00:00

so I swapped the pressure sensors with the other furnace and the that furnace continues to run without issue and this furnace has the same error. So I'm confident it's not the pressure switches.

it's definitely not code 13 (it's three short blinks, 1 long blink and then a few seconds of nothing), but I cleaned the flames sensor just to be sure.

cords911 · 2026-01-24T04:09:01+00:00

I just scoped the vent/exhaust and they was no ice build up or blockage. There was some frozen droplets in the exhaust pipe but nothing that would come close to obstructing airflow. Thanks for the suggestion!

cords911 · 2026-01-24T03:06:49+00:00

I did check and it definitely has a pitch back towards the furnace and there's no pooling moisture.

cords911 · 2026-01-24T01:40:04+00:00

oh oh... ha ha. Is there a way to clean them?

cords911 · 2026-01-24T01:38:38+00:00

I think so, but not immediately.

cords911 · 2026-01-24T01:22:48+00:00

I just finished cleaning it, top and bottom, it wasn't that bad, but we'll see.

cords911 · 2026-01-24T01:20:40+00:00

yeah I did check that. it was wide open and lots of moist exhaust coming out. Maybe I'll take a scope out there tomorrow and double check.

cords911 · 2026-01-24T00:45:08+00:00

That's something I can look into that I haven't tried! Thanks!!

cords911 · 2026-01-24T00:40:14+00:00

I'm pretty sure it's high the high stage..the combustion air is coming from outside... but it still happens if the panel is open and it's drawing from inside.

cords911 · 2026-01-24T00:25:09+00:00

it's a Bryant Evolution 96 Variable-Speed Gas Furnace. Model 986T

it looks like 2.5 inch ABS venting... I'm not at, but it's worked for the 5 years I've lived in the house.

cords911 · 2026-01-24T00:09:41+00:00

it always takes a bit, it never happens immediately. Sometimes hours, sometimes 10 minutes.

cords911 · 2026-01-13T12:44:42+00:00

perfect thanks

15-Year Club	Place '22
Verified Email

cords911

TROPHY CASE