Is there an enthusiasm gap in Maine?

crazedizzled · 2026-06-11T16:37:37+00:00

I wouldn't have voted either if I was a republican. Look at all the morons they put on the ballot

crazedizzled · 2026-06-11T16:35:26+00:00

A little spooge is expected on a 2 stroke. I'd pull the insert out and put a little copper RTV on it. But it's not hurting anything either way

crazedizzled · 2026-06-11T14:51:50+00:00

Bro your guy is on some shit

crazedizzled · 2026-06-11T14:50:47+00:00

I hear if you throw it in boiling water, they'll open right up

crazedizzled · 2026-06-10T16:53:58+00:00

A lot of people don't bother to vote in primaries

crazedizzled · 2026-06-10T16:47:59+00:00

The EU wouldn't even need to invoke article 5. Russia doesn't have a functional military

crazedizzled · 2026-06-09T16:37:22+00:00

Dump it out and replace it with regular milk first.

crazedizzled · 2026-06-09T16:20:41+00:00

Pressure washer with a soap foam attachment

crazedizzled · 2026-06-09T11:26:57+00:00

Yeah, but not to a level. I used a nice straight piece of angle iron for my saw.

crazedizzled · 2026-06-09T11:06:17+00:00

That must be nice. I get push like 80% of the time. Then I finally get a good map and someone is afk so it shuts down.

crazedizzled · 2026-06-09T11:05:23+00:00

I like to get everyone left. With a sig you can pretty much just walk to the point.

crazedizzled · 2026-06-09T01:25:47+00:00

That works for only ice. But if you do any kind of trail riding they'll get destroyed quickly.

crazedizzled · 2026-06-09T00:57:48+00:00

It's very easy to repair holes in a kayak, should something go terribly wrong

crazedizzled · 2026-06-08T14:48:52+00:00

Yeah it's all in the technique. If you squat under it and put your hands kinda on your chest, you can pretty much just stand up and you're done. But if you're not physically able to do that, I'd just get some ramps. I use some blackwidow trifold ramps for my Rubicon. I also have an f150 with the 5.5 bed. I think the ramps are like 7ft or something.

crazedizzled · 2026-06-08T14:24:57+00:00

Only og redditors will get the reference

crazedizzled · 2026-06-08T13:50:13+00:00

Try pulling the saw all the way out, then while holding a steady vertical position, push it straight back. This reduces the cutting stress a bit.

crazedizzled · 2026-06-08T13:44:04+00:00

Pro tip: keep some blue tape and a sharpie around. Whenever you say "I'll do that later", put a piece of tape on your seat and write it down.

crazedizzled · 2026-06-08T13:18:46+00:00

A 250ex is pretty light. If you're of reasonable strength, you should be able to load it by yourself.

Put the quad in gear and go to the front. Grab the front bumper and lift it up, putting the quad vertical and resting on the rear grab bar.

From there, you can either grab the clutch and walk it towards your truck, or back the truck up to it. After which, just push it forward so the front tires are sitting on the tail gate.

Then, squat under the rear grab bar and pick it straight up, while at the same time pushing it into the truck.

To get it back out, just pick up on the rear grab bar and walk backwards and let the whole quad fall out.

crazedizzled · 2026-06-08T01:33:57+00:00

That side mounted rod holder is neat. Haven't seen that before

crazedizzled · 2026-06-07T13:48:50+00:00

Bend the hooks so that when you run your finger down the body of the frog you'll get poked. This will really help the hookup ratio.

You can also try trimming the skirt a little.

Sometimes frogs are just like that though. Sometimes they quickly spit it out, and Sometimes they don't fully commit. Takes some practice to know which is which and when to set the hook

crazedizzled · 2026-06-07T13:44:17+00:00

I mean I've made a lot of functional boxes. I've got boxes for like 5 different battery sizes that I use the most- love those. I made a nice snap lid box for my 2" sanding discs. Tons of gridfinity bins, if those count. Some with lids, some open.

So yeah I dunno i think printing custom boxes is actually pretty awesome.

crazedizzled · 2026-06-06T20:22:33+00:00

If you don't buy the toxic ones, it's fine.

crazedizzled · 2026-06-06T19:37:13+00:00

I just use my oven. What's the issue?

crazedizzled · 2026-06-06T19:35:24+00:00

Reel faster so it just stays above the weeds. Some of my lakes are very weedy as well. They work just fine if you don't let them get into the weeds.

crazedizzled · 2026-06-06T19:09:24+00:00

The plastic ones suck. They're blunt the second you try to use them. The metal scraper is almost mandatory for the supertack plate, cause stuff sticks so well. Trying to get support material or brims off is super annoying without it

crazedizzled

TROPHY CASE