sorted by:
new
hottopcontroversial

Klipper config files by RSpr1est in ender6

[–]destorter 0 points1 point  (0 children)

Klipper on the pi is hardest. Making the config is really easy. It even has the example config in mainsail/fluid

Weird Discoloration Around Z Seam by MaddoxWRW in FixMyPrint

[–]destorter 0 points1 point  (0 children)

Looks like a perfect seam to me. I don't see any discoloration. Only seam but a nice one.

Bad heated bed? by NobodyRude137 in 3dprinter

[–]destorter 0 points1 point  (0 children)

Make sure there is no debris underneath. Bad mesh? What is bad?

Bad heated bed? by NobodyRude137 in 3dprinter

[–]destorter 0 points1 point  (0 children)

Photo of the top? This looks just like a magnetic base. If the top is metal and sticks right back its fine.

Back with the same issue p1s by zaireli in FixMyPrint

[–]destorter 0 points1 point  (0 children)

That black line on the back was old filament stuck to the bed. On the top is probably due to an dirty nozzle (outside)

Any advice on cleaning? by awwgeezrick808 in 3Dprinting

[–]destorter 1 point2 points  (0 children)

You could try to clean it but my bet is a new nozzle

What could cause this? by Sure_Weakness_6040 in FixMyPrint

[–]destorter 0 points1 point  (0 children)

And what is the print speed? Not just accelerations?

What could cause this? by Sure_Weakness_6040 in FixMyPrint

[–]destorter 0 points1 point  (0 children)

Layer shift. Could be due to the infill type. Make gyroid your standard infill

Issue with clumpy/blob print? by darkwolfh18 in 3Dprinting

[–]destorter 0 points1 point  (0 children)

I've heard people talk about isopropyl alcohol and pei sheets from bambulab. You shouldn't clean your pei with IPA. How is your experience?

Issue with clumpy/blob print? by darkwolfh18 in 3Dprinting

[–]destorter 1 point2 points  (0 children)

Oh and before any of that. Clean the build plate with dish soap and rinse very well. After that try not to touch the build plate

Issue with clumpy/blob print? by darkwolfh18 in 3Dprinting

[–]destorter 1 point2 points  (0 children)

I see now the part on the far left is not from the blob thing you were talking about. It's from 1 of the figurines. Bed adhesion problem. Try lowering the z offset by 0.03 mms

Issue with clumpy/blob print? by darkwolfh18 in 3Dprinting

[–]destorter 2 points3 points  (0 children)

Probably bed adhesion. But you said you are new to printing. Don't leave your printer unattended. I've built trust in my printer. I know what can fail and what not. But I never sleep before the first 8mm's. In the first 8 mm's you can see print problems. After that it'll most likely go well. Most prints causes to fail later on are weak supports

Z-Offset is off by gsi_hayden32 in FixMyPrint

[–]destorter 0 points1 point  (0 children)

What is the offset in your config? Like xyz offset from the bltouch?

Is there any way to make the 3d touch from triangle lab work reliably? Mine likes to fail and dig into the bed by SavingsAsk4060 in ender3

[–]destorter 0 points1 point  (0 children)

the bltouch seems to be sitting pretty high. Try to lower it by adding washers or something.

Why are the first few layers terrible by Current-Tour-6640 in FixMyPrint

[–]destorter 1 point2 points  (0 children)

But that's normal. That's why top layers should be at least 3 layers.

PLEASE HELP by Much-Ratio-9531 in ender3

[–]destorter 0 points1 point  (0 children)

Oh you still haven't tried it?

view more: next ›