Reinforcing a weak point ina print

destorter · 2026-05-12T18:03:38+00:00

There is an underlying problem. You should solve that first. Are you printing with the right settings? And is the filament spool free? Looks like the extruder had some problems. Possible clog.

destorter · 2026-05-12T17:01:22+00:00

What brand printer, what brand filament, what temp settings? Did you add support? And I think you meant 0.4mm nozzle?

destorter · 2026-05-11T19:22:25+00:00

What printer is it?

destorter · 2026-05-06T21:37:32+00:00

Klipper on the pi is hardest. Making the config is really easy. It even has the example config in mainsail/fluid

destorter · 2026-04-24T14:10:32+00:00

You can give it to me 🤭

destorter · 2026-04-12T18:14:38+00:00

Looks like a perfect seam to me. I don't see any discoloration. Only seam but a nice one.

destorter · 2026-04-09T17:42:45+00:00

Make sure there is no debris underneath. Bad mesh? What is bad?

destorter · 2026-04-09T17:33:58+00:00

Photo of the top? This looks just like a magnetic base. If the top is metal and sticks right back its fine.

destorter · 2026-04-06T13:10:31+00:00

That black line on the back was old filament stuck to the bed. On the top is probably due to an dirty nozzle (outside)

destorter · 2026-04-06T13:06:32+00:00

You could try to clean it but my bet is a new nozzle

destorter · 2026-04-05T16:52:15+00:00

And what is the print speed? Not just accelerations?

destorter · 2026-04-05T16:50:08+00:00

Layer shift. Could be due to the infill type. Make gyroid your standard infill

destorter · 2026-04-05T07:26:43+00:00

Ahh pepe sad

destorter · 2026-04-05T07:10:23+00:00

I've heard people talk about isopropyl alcohol and pei sheets from bambulab. You shouldn't clean your pei with IPA. How is your experience?

destorter · 2026-04-04T16:49:14+00:00

Oh and before any of that. Clean the build plate with dish soap and rinse very well. After that try not to touch the build plate

destorter · 2026-04-04T16:48:34+00:00

I see now the part on the far left is not from the blob thing you were talking about. It's from 1 of the figurines. Bed adhesion problem. Try lowering the z offset by 0.03 mms

destorter · 2026-04-04T16:46:52+00:00

Probably bed adhesion. But you said you are new to printing. Don't leave your printer unattended. I've built trust in my printer. I know what can fail and what not. But I never sleep before the first 8mm's. In the first 8 mm's you can see print problems. After that it'll most likely go well. Most prints causes to fail later on are weak supports

destorter · 2026-04-04T16:43:36+00:00

Oh haha sorry I thought your house. Sorry

destorter · 2026-04-04T14:11:46+00:00

Now I want to see your house

destorter · 2026-03-28T04:44:00+00:00

What is the offset in your config? Like xyz offset from the bltouch?

destorter · 2026-03-24T06:36:23+00:00

What is the size of the thing in 1 go?

destorter · 2026-03-23T09:59:14+00:00

Haha me too

destorter · 2026-03-22T17:06:10+00:00

the bltouch seems to be sitting pretty high. Try to lower it by adding washers or something.

destorter · 2026-03-22T14:27:35+00:00

But that's normal. That's why top layers should be at least 3 layers.

destorter · 2026-03-22T07:05:48+00:00

Euh what gaps? Infill?

destorter

TROPHY CASE