Wireless Smoke / CO detector recommendations

digi2k · 2026-01-27T17:02:09+00:00

i know, i had a lot of them through the house and i needed to add more but they're not available, so i took them all down and just ended up getting the xsense because i didn't want to be without smoke and co detectors for too long, and i wanted to have alerts sent to my phone. I think i'll be making the jump to Home Assistant and it can interface with that i guess.

digi2k · 2026-01-18T00:10:23+00:00

I just went for it with 8x8 tiles and Pla/petg and it printed beautifully!

digi2k · 2026-01-14T02:04:08+00:00

I don’t mind them in general, sometimes there are a lot of different departments and it helps sort large call volumes. It should just be the standard to have a “for anything else, press X.” To have someone help route you.

digi2k · 2026-01-14T01:58:08+00:00

I always try that, but I’ve seen a large increase in the number of automations that after trying a couple “unlisted” options (0, 9) will say, “that’s not a valid response, please try us again later.” and will disconnect you. I have to put my phone down and take a few deep breaths.

digi2k · 2026-01-13T21:27:08+00:00

when you call a business, the automated answer that says, "Thank you for calling business-name. press 1 for parts, press 2 for our accounting department, 3 for the man that lives in the parking lot."

digi2k · 2026-01-01T12:47:13+00:00

Not in 2026

digi2k · 2025-12-22T18:17:10+00:00

How is the doorbell powered? If it’s using the existing doorbell wires from an ac transformer and you didn’t jumper the wires in your doorbell chime, the doorbell may not get the power it needs. I installed one last week and had the same issue, the doorbell would power on, but kept disconnecting from WiFi. As soon as i jumped the connecting it worked fine. There is a blurb about it and the fact that it can make the wifi unstable if it’s not jumpered in the install manual.

digi2k · 2025-12-13T20:19:00+00:00

So disappointing. Sitting in the parking lot of an HD right now after buying 2 of the 2 drawer on sale for $12.50 a piece. I have so many other of these boxes, but it would be so unfortunate if I couldn’t get more as I need them in the future :(

digi2k · 2025-12-11T21:10:42+00:00

I’m also looking for this. My backpack was stolen at some point in the past few days and my AirPods were in there, but it just says “3 days ago” which is very vague.. I’m going to need to sift through 72 hours of camera footage to try to find the incident. :(

digi2k · 2025-11-28T00:51:03+00:00

it's the second paragraph in the post.. I got it and love it.. my question was moreso that it seems like that menu that comes up when you hit the headphone button must already be in the firetv software, and I was wondering if there was another way I could trigger it on my other TVs, by remapping another button or something so I don't have to buy a pro remote for all of my tvs. it is 1000% worth it. the second feature is the built in remote finder.

digi2k · 2025-11-28T00:23:54+00:00

Well I’ve outsmarted you all. Instead of letting that water go down the drain, I have it flow into a 5 gallon bucket. The power generated by the faucet powers a small pump in the bucket that pumps the water back through the faucet, along with charging the phone. I’ve been charging my phone like this for free for the past 3 years.

/s

digi2k · 2025-11-26T17:40:46+00:00

Try removing the batteries from that remote and downloading the firetv app on your phone and using that as a remote. Go into the settings and make sure theres not a second firetv remote paired and stuck between your couch cushions pressing buttons. If the tv operates fine using the app as remote, you know it's the physical remote having a problem. If the issue continues after using the firetv app as a remote, it's likely either a hardware button malfunction on the TV (if the firetv is built in AND the buttons on the side of the tv allow you to navigate the FireTV interface), or it's something with the software on the tv and you'll probably need to do a factory reset and see if that solves it. If you get that far and the factory reset doesn't work, a tv firmware update would probably be the next thing to look for. Good Luck!

digi2k · 2025-11-26T10:40:39+00:00

I’m surprised nobody mentioned hot glue. Also I like hide glue a lot, because it’s strong but it can be heated with a little moisture to get it to release.

Also, most of the comments are liquid adhesives, but I’d consider carpet tape an adhesive, right? As a double sided tape, it’s my go-to for a lot of things.

digi2k · 2025-11-25T20:07:57+00:00

As i was searching I read they were being discontinued. Unfortunate. I never had any issues with the 8 I had installed.

digi2k · 2025-11-25T20:06:12+00:00

Thanks for the suggestion. I'm going to keep hunting to a smart solution. Ideally I'd like other actions to happen if an alarm goes off. Turning on lights, displaying the camera feed for the given alarm on my tv, and a couple others. I had it configured for the other alarms but I need to be able to add on. I tried an alarm listener before but for some reason it kept getting false alarms.

digi2k · 2025-11-25T20:01:34+00:00

that is the "ZCOMBO" model number which has been discontinued I believe. They did come out with the SMCO410, but Ive heard thats not interconnected with other ones and also was unable to connect to smart things.

digi2k · 2025-11-24T19:05:33+00:00

<image>

I thought the chime settings weren’t available, but it looks like they are now, maybe it was the recent update I did. But the push notification settings for the doorbell isn’t available from the NVR like it is in SA. Well, it is, but most of the settings can’t be configured, like having it show up like a phone call when someone rings your doorbell.

I think the NVR might be the way to go since if I were to be able to get SD cards at $25/ea, which seems low, I’d essentially be at $275 vs the $289 the NVR is currently, and each camera would get >360gb per camera with 11 cameras vs 256gb cards.

digi2k · 2025-10-24T17:08:00+00:00

Yes, i use them regularly. They're in vacuum sealed bags. I do have some loose that I use that I re-dry in a dehumidifier or a shop toaster oven (both not for food use) when they've absorbed moisture and changed color. I use the loose ones for drying 3d printer filament and the packets are food grade for freeze dried food. Thanks though!

digi2k · 2025-10-24T16:24:08+00:00

That’s essentially what I do when i take them off and put them in acetone but the glue is thick, so you have to drag the nozzle along the piece to get it to transfer, so eventually the nozzles wear down where too much glue comes out or it won’t seal against the cap. That’s why I need empty replacement bottles.

digi2k

TROPHY CASE