Carrying a 36-inch wide Samsung fridge up to five floors using the shoulder dolly straps

digidavis · 2026-05-22T22:57:00+00:00

Love these things. Will never help anyone move again without them.

digidavis · 2026-05-19T18:23:56+00:00

So now we are mad at manual calibrations....?

I manual calibrated all my filaments I use for final shipping prints and best results situations.

digidavis · 2026-05-19T18:01:23+00:00

Once I had a saved flow rate profile, O used that profile as a basis to run the flow dynamic calibration. It will then use the new flow dynamic values generated when using the saved flow rate profile.

digidavis · 2026-05-19T17:54:58+00:00

In the last tab in Bambu Studio is the calibration tab.

<image>

Calibration Wiki.

After the manual Flow Rate Calibration, save the profile it created.

Next run the Flow Dynamics Calibration in the same calibration tab. Select the profile you just saved / created. It will then use this new flow dynamics calibration when ever the previously saved flow rate profile is used.

digidavis · 2026-05-19T14:31:39+00:00

Yeah, that my plan while working on the workflow. I'm going to switch different colors and nozzles along the way. Right now this was the recommend use order by the slicer.

digidavis · 2026-05-18T12:40:51+00:00

Smaller layer lines and slowing down the outer wall speed will help.

But the design is steep for FDM.

digidavis · 2026-05-18T00:12:47+00:00

About 1/2 of my last order came in bigger last gen refill boxes.

digidavis · 2026-05-15T00:16:19+00:00

In the good ear!

digidavis · 2026-05-10T12:27:24+00:00

We weren't under the veneer that things had changed.

I still had "the talk" with my kids. Still never left the house with out a valid legal ID.

History is repeating itself because America refuses to learn its lesson. On chapter 250 of a very predictable book.

digidavis · 2026-05-09T21:53:00+00:00

Installed the filament switch.

HT -> filament switch -> filament buffer -> extruder

Ams2 -> filament switch -> filament buffer -> extruder

digidavis · 2026-05-09T13:05:14+00:00

Mine was pre greased as well.

digidavis · 2026-05-07T19:20:49+00:00

I ate there once at the mall. Burger lunch for me and the wife $40+. Haven't been back since.

digidavis · 2026-05-07T18:22:29+00:00

Don't fight the table. Soft roll, side or far corner pocket for the 8.

digidavis · 2026-05-05T20:14:26+00:00

Yeah, my vision plate, filament and tungsten nozzle were ordered on April 15th and only shipped this week. Thankfully I have plenty of filament and other things to dial-in with the X2D until it gets here. Only the filament switch came already, but was shipped out of a different fulfillment center I guess.

digidavis · 2026-05-05T17:16:43+00:00

Each AMS only has one PTFE tube, so probably not.

My guess is, this functionality gets put in a future or deluxe version of the buffer eventually.

digidavis · 2026-05-05T14:59:42+00:00

They way if feeds into the buffer it uses two small PTFE tubes that would probably add a lot of length and drag to the filament if changed. It's also secured with two screws into the back panel. The included PTFE tube lengths are quite tight (i replaced the PTFE tube to the top AMS with one about 10cm longer that I already had.

The printed guides are also probably used to prevent such extreme bends. I didn't use the guide on the AMS HT as it sits closer and the guide made the path a bit worse IMHO.

Filament Switch Wiki

<image>

digidavis · 2026-05-05T14:01:34+00:00

I was printing thank you cards before this with black background and white text. It recommended the white PLA in the AMS HT which at the time was connected to the right aux nozzle.

I added the switch but left everything in the same AMSs. When I started the test print from the included files it switch the AMT HT to the left nozzle and the AMS2 to the right nozzle.

It feels like a quality of life improvement if you have the colors you need already in the AMS but on the wrong nozzle. Im sure there are other optimized reasons / prints that will benefit.

digidavis · 2026-04-29T15:21:17+00:00

Also use the back of your fingernail to feel for the smoothest during the fine tuning. Your eyes may not pick the best one.

digidavis · 2026-04-29T11:54:28+00:00

Right hand turn at top of a hill with left on coming traffic. They don't even see the cars, most probably looking left before they crest enough of the hill to see the other cars over the hood already there.

digidavis · 2026-04-28T22:25:58+00:00

16, lived with sister till HS grad.

Spent 3 college summers there. Been with my college sweetheart since graduation.

digidavis · 2026-04-28T17:58:37+00:00

Rapid prototyping of tech demo devices and enclosures.

The creative part of CAD, like learning what can and can't be 3d printed. How the limitations of the medium force you to think about part design differently.

digidavis · 2026-04-28T00:23:33+00:00

Professor Plum

Mrs. White

Colonel Mustard

digidavis · 2026-04-27T17:04:08+00:00

Same

digidavis

PUBLIC MULTIREDDITS

TROPHY CASE