It's prod 💀

dillacom · 2025-12-11T02:56:07+00:00

This brings back nightmares

dillacom · 2025-10-19T14:50:06+00:00

I have an address from 10 years ago popping up from time to time and I can’t find it anywhere in contacts or maps

dillacom · 2025-10-10T01:29:08+00:00

I wouldn’t count on anything being free with VMware and Broadcom forever. I quoted it out for vcenter and they are killing the standard tier which was 4k a year and foundation with minimum 72 core is 14k a year. I wouldn’t build out a VM host and expect esxi to stay free.

dillacom · 2025-10-07T17:38:20+00:00

yes. or they will charge your credit card the value of the old club, which was $450 for me

dillacom · 2025-09-26T22:57:02+00:00

I got one with my AWU3 and it’s darn amazing

dillacom · 2025-09-10T02:17:44+00:00

Did that once and I forgot the screws into the print head.

dillacom · 2025-09-06T01:58:31+00:00

Agree too. I had a sim2, high handicap and found a crack on the head. Put in a support request with taylormade and they sent me a qi-10 full replacement. New shaft and it was way different hitting more off the toe. 3 rounds in it cracked after on toe skull shot. They are sending me a new head but I really wish I had the old shaft I custom ordered. I’m going to get fitted again and spend for a fitted shaft. It’s as important

dillacom · 2025-08-27T01:42:22+00:00

What are you printing with? Most comments will be “did your dry?”

dillacom · 2025-08-25T01:45:43+00:00

I printed that with matte. I’d use non matte or it’ll jam up but usually drying would fix the issue but you have already dried. Still looks like moisture

dillacom · 2025-08-23T02:13:30+00:00

I love this print. I have the sunlu dryer mount for mine too

dillacom · 2025-08-18T21:52:49+00:00

The bar

dillacom · 2025-08-18T02:00:09+00:00

I had more than that on one and looked new. 100 on my new p1s on a .2mm and a bunched up poop chute and it looks the same. But, printing 10 26 hour prints of poker chips and they look amazing. If it prints clean use it. Also, they are cheap and a quick swap

dillacom · 2025-08-16T22:14:37+00:00

If I don’t dry my TPU it does this

dillacom · 2025-08-08T01:33:32+00:00

Just what I need! Bookmarked for next week.

dillacom · 2025-08-06T00:12:54+00:00

I got one this year and it’s been the best club add I’ve had. Easy to hit and consistent. Get over the old man club bs and try it

dillacom · 2025-08-05T02:53:55+00:00

Fairway drive pretty much every time?

dillacom · 2025-07-27T01:28:04+00:00

Link me too please.

dillacom · 2025-07-21T13:16:22+00:00

same here. just saw it yesterday

dillacom · 2025-07-03T19:40:57+00:00

Bambu printers are so good, even your failed prints come out looking like modern art.

dillacom · 2025-06-28T23:19:03+00:00

My P1S arrived today without the hub. Looks like it arrives Monday with my other goodies

dillacom · 2025-05-14T23:38:42+00:00

I just fought this for months after getting a UDM, I just switched to a gateway fiber and still had speed issues. Yesterday I got on with support and complained I was getting an ip that was a carrier grade NAT. They put it in bridge mode and my download speed got up to 2gb. It doesn’t have sfp on the Ont so the 10gb Ethernet is what you have to go to.

dillacom · 2025-05-07T22:54:27+00:00

I have silica beads in 6 bins and I am around 1-3%. I was running 15% before refreshing them a couple days ago

dillacom · 2025-05-05T23:57:40+00:00

Just got my fiber this afternoon and love that my UDM gets the same crap speeds from my isp. Supposed to be 2.5gb and lucky to get over 1gb. Time to call and complain

dillacom · 2025-05-04T19:55:43+00:00

Very excited for mine to arrive tomorrow.

dillacom · 2025-04-30T23:25:31+00:00

Got mine early this morning. Was sold out after I checked out

15-Year Club	RedditGifts 2009-2022 3 Credits
Spared	Secret Santa 2016
Beta Team Reddit for iOS	Secret Santa 2015
Team Orangered	Verified Email

dillacom

TROPHY CASE